skip to footer block
DRA Qualtech DWTSMT14X1.75 m14 x 1.75 HSS Plug Tap P13389254DRA-DWTSMT14X1-75 https://cdnimages.opentip.com/full/DRA/DRA-DWTSMT14X1-75.jpg Qualtech DWTSMT14X1.75 m14 x 1.75 HSS Plug Tap Manufacturer Part Number: dwtsmt14x1.75Used to make new threads or re-thread damaged and/or jammed threadsHand Taps are the most versatile taps for hand use. They are also appropriate for tapping the vast majority of materials in through or blind holed conditions.Hand Taps come in three styles Taper Plug or Bottom.. Taper Style: Starts the thread square with the workpiece. Plug Style: Generally used in thru holes. Bottom Style: Generate the thread to the bottom of the hole. A tap set contains 1 taper 1 plug and 1 bottoming tap.Size :m14 x 1.75Material :High Speed SteelFinish :Uncoated (Bright)Cutting Direction :Right HandTap Size :m14Threads Per Inch :1.75 13389254 887861074193 0.2900lbs 0.00 0.00 0.00
Qualtech
20.64 2026-08-23 69 In Stock
customer review - by , March 3, 2025
5/ 5stars
Broke first time using it! Started cleaning threads of one hole and tap broke right off, very little effort. Other reviewer mentioned a similar experience. Never buying this garbage ever again.
customer review - by , March 3, 2025
5/ 5stars
Used this to chase all threads on my Mazda rotary engine oil pan mounting bolt holes. Would work on RX7, RX8, etc. Worked great to clean them all out of old sealant.
customer review - by , March 3, 2025
5/ 5stars
When tapping a hole it broke. The Drill America tap was better made than the one I broke. I also cuts threads much easier and the chips are finer. As other taps I have break or are worn out I will replace them with Drill America taps. Very satisfied.
customer review - by , March 3, 2025
5/ 5stars
Had to thread a blind axial hole in a piece of aluminum rod; this tap did the job easily and accurately. Cutting oil is always recommended when tapping metal, and I used some, but I'm pretty sure the tap would have cut clean threads without it, given that aluminum is so soft. Still, nice product at a fair price.
customer review - by , February 2, 2025
5/ 5stars
Works very well. Good value.
customer review - by , January 1, 2025
5/ 5stars
Worked great. Go slow and use tap oil. Back it out and clean the area of debris as you go. Don’t force it.
customer review - by , November 11, 2024
5/ 5stars
Worked great! Ran an appropriate socket, I have a craftsman multipoint socket that went on the end of this nice to clean up the threads.
customer review - by , October 10, 2024
5/ 5stars
Nice taps
customer review - by , September 9, 2024
4/ 5stars
Must have! Delivery by 8am. Only used once and did the job!
customer review - by , September 9, 2024
5/ 5stars
I've broken taps before. This one stood up to some high but careful pressure to thread a hole in steel.
  »  
  »  
  »  
  »  
  »  

Qualtech DWTSMT14X1.75 m14 x 1.75 HSS Plug Tap

stars Rating 5 | 67 reviews
Brand Qualtech
Shop more from DRA
UPC: 887861074193
SKU: DRA-P-410-1
Price:
$20.64Free shipping on orders over $350.00 on select DRA- items. Details
Tapsize:
Threadsperinch:
Quantity:
69 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Pricing Note

Free Shipping Promotion: Buy more items from the same series, product code beginning with DRA-, and you can get free shipping for an order of over  $350.00  consisting of only DRA- series products.

Product Description

Manufacturer Part Number: dwtsmt14x1.75

  • Used to make new threads or re-thread damaged and/or jammed threads
  • Hand Taps are the most versatile taps for hand use. They are also appropriate for tapping the vast majority of materials in through or blind holed conditions.
  • Hand Taps come in three styles Taper Plug or Bottom.. Taper Style: Starts the thread square with the workpiece. Plug Style: Generally used in thru holes. Bottom Style: Generate the thread to the bottom of the hole. A tap set contains 1 taper 1 plug and 1 bottoming tap.


    • warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
    Need more information?
    Our staff are available to answer any questions you may have about this item
    Request More Information

    Look Similar Items By Category

    Industrial & Scientific > Cutting Tools > Threading Taps > Hand Threading Taps
    Tools & Home Improvement > Power & Hand Tools > Hand Tools > Taps & Dies > Taps > Hand Threading Taps
    Customer Reviews
    5 out of 5
    see all 67 reviews
    5 stars
    56
    4 stars
    4
    3 stars
    1
    2 stars
    2
    1 stars
    4
    Write a Review
    By Michael Kinner
    Date: March 17, 2025
    Broke first time using it! Started cleaning threads of one hole and tap broke right off, very little effort. Other reviewer mentioned a similar experience. Never buying this garbage ever again.
    Rating: 5 stars [5 of 5 Stars!]
    By neal
    Date: March 14, 2025
    Used this to chase all threads on my Mazda rotary engine oil pan mounting bolt holes. Would work on RX7, RX8, etc. Worked great to clean them all out of old sealant.
    Rating: 5 stars [5 of 5 Stars!]
    By Johnny 5
    Date: March 08, 2025
    When tapping a hole it broke. The Drill America tap was better made than the one I broke. I also cuts threads much easier and the chips are finer. As other taps I have break or are worn out I will replace them with Drill America taps. Very satisfied.
    Rating: 5 stars [5 of 5 Stars!]
    By Tony B.
    Date: March 06, 2025
    Had to thread a blind axial hole in a piece of aluminum rod; this tap did the job easily and accurately. Cutting oil is always recommended when tapping metal, and I used some, but I'm pretty sure the tap would have cut clean threads without it, given that aluminum is so soft. Still, nice product at a fair price.
    Rating: 5 stars [5 of 5 Stars!]
    By A Customer
    Date: February 07, 2025
    Works very well. Good value.
    Rating: 5 stars [5 of 5 Stars!]
    By Brian
    Date: January 28, 2025
    Worked great. Go slow and use tap oil. Back it out and clean the area of debris as you go. Don’t force it.
    Rating: 5 stars [5 of 5 Stars!]
    Items 1 - 6 of 67 reviews
     1  2  3  4  5 ...  [Next]