5 out of 5
Customer Reviews
By
Michael Kinner
Date: December 12, 2025
Broke first time using it! Started cleaning threads of one hole and tap broke right off, very little effort. Other reviewer mentioned a similar experience. Never buying this garbage ever again.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
neal
Date: December 06, 2025
Used this to chase all threads on my Mazda rotary engine oil pan mounting bolt holes. Would work on RX7, RX8, etc. Worked great to clean them all out of old sealant.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Johnny 5
Date: November 25, 2025
When tapping a hole it broke. The Drill America tap was better made than the one I broke. I also cuts threads much easier and the chips are finer. As other taps I have break or are worn out I will replace them with Drill America taps. Very satisfied.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Tony B.
Date: November 22, 2025
Had to thread a blind axial hole in a piece of aluminum rod; this tap did the job easily and accurately. Cutting oil is always recommended when tapping metal, and I used some, but I'm pretty sure the tap would have cut clean threads without it, given that aluminum is so soft. Still, nice product at a fair price.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: October 04, 2025
Works very well. Good value.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
prius dude
Date: May 03, 2025
Worked great! Ran an appropriate socket, I have a craftsman multipoint socket that went on the end of this nice to clean up the threads.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
RedHornet
Date: March 15, 2025
Nice taps
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jeff Peterson
Date: February 09, 2025
Must have! Delivery by 8am. Only used once and did the job!
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Trevor Fitzroy
Date: December 28, 2024
I've broken taps before. This one stood up to some high but careful pressure to thread a hole in steel.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
carolyn
Date: December 19, 2024
Have yet to use
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Justin g.
Date: November 17, 2024
I had to rethread my lug nuts and it worked like a charm!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Paul
Date: October 26, 2024
Excellent set of taps for starting and bottom threading blind holes. Strong taps, very sharp. Accurate threads. I use these to cut plug threads in hardened steel crankshafts. The taps laughed at cutting threads in forged steel..
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
RDWood
Date: October 22, 2024
Uncommon tap size to find. I usually order tools like this from McMaster Carr but they didn't have it. I used it on my VW Solex carburetor after I stripped a thread in the housing. Used JB Weld to fill the hole, then drilled and re-tapped the hole with this tap. Worked great.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Fred M
Date: October 10, 2024
I messed up a thread on my vehicle and this product was the tool for my repair.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Miguel Ocasio
Date: October 04, 2024
The product was great I love the way it works
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Michael D.
Date: September 22, 2024
This set is pretty durable, and it is at a reasonable price. specific size. I recommend it.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Phil
Date: September 09, 2024
I was installing a tow hitch on our vehicle, and the bolt holes had some corrosion and Road grime preventing the bolt from biting. So I used this to chase the threads and installation was easy after that! This size wasn't available in the kits I looked at, so I was happy to see it here.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
James R. Carpenter
Date: September 09, 2024
Cut well but bottoming tap snapped under moderate load.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
D. Anderson
Date: September 06, 2024
Ordered this tap to cut threads in a through-hole rotor shaft so the rotor could be removed with a forcing screw. The tap arrived in a small, clear plastic case inside of a plastic bag. Nifty little case for storage. The tap's fit and finish were excellent with sharply defined threads throughout and a very nice gradual taper to start. It alligned and cut the threads smoothly and with ease. I used a Lisle tap socket and ratchet to drive it with 80W-90 gear lube for cutting oil. I'm very pleased with the tap and would definitely order another Drill America tap or drilling tool when the need arises.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Karl Kroner
Date: September 02, 2024
Just what I ordered.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]