skip to footer block
PEX Parts Express Inline AGC Fuse Holder P1248070PEX-070-609 https://cdnimages.opentip.com/full/PEX/PEX-070-609.jpg Parts Express Inline AGC Fuse Holder Standard 1-1/4\" fuseholder.Overview: Inline AGC Fuse HolderStandard 1-1/4\" fuseholder. Overall length 2-1/4\" with 18 gauge wires.Specification: Product DetailsBrandParts ExpressPart Number070-609UPC844632017322Unit of MeasureEachWeight0.0198Manuals & Resources: Parts Express Standard Warranty 1248070 844632017322 0.0200lbs 0.00 0.00 0.00
Parts Express
1.29 2026-04-25 718 In Stock
customer review - by , November 11, 2024
5/ 5stars
WARNING: THESE ARE DANGEROUS AND DO NOT BLOW WITH 5x THE CURRENT! This is a products liability/manufacturing defect case waiting to happen. The sole purpose of the fuse is to blow when the current is too high. Somehow I’m able to get 5 A through a 1 A fuse. A small amount of wiggle room is normal, but not 5x the current! The filament simply starts glowing red and heats up SIGNIFICANTLY. I tested my circuit before putting it in its casing, but if I didn’t there is no doubt in my mind that it would have melted the plastic after a few minutes. (I used the through-hole PCB clips, not the in-line component. )Less importantly, they arrived with the plastic box open, so every fuse spilled out and they were all mixed together in the plastic wrap. I was able to separate them myself, but that is a major pain. (And yes, I confirmed that the fuse I used above was, in fact, a 1 A fuse by the marking “F 1A L 250V”.)
customer review - by , August 8, 2024
5/ 5stars
Will work well for my wiring project
customer review - by , April 4, 2024
5/ 5stars
Great value for the money!
customer review - by , March 3, 2024
5/ 5stars
Quality Items for a Great Price !!
customer review - by , September 9, 2023
5/ 5stars
Wired it right into my harness, needed a peaceable link wire gauge was acceptable
customer review - by , July 7, 2023
5/ 5stars
The fuses are in compartments and a table tells you the current rating. They are all mixed up so you can't figure out the correct size. They are not marked on the fuse either. The first fuse I used was open circuit even before I installed it. I needed a 1.5 amp fuse but they only had 2 amp fuses so I installed one. It lasted one dat then opened. It obviously wasn't a 2 amp rated fuse even though the cable on the box indicated that it was. I ended up installing a fuse labeled 15 amp even though the fuse link in it was very thin. You can't trust the fuse size chart on the box. The fuse holders were OK though.
customer review - by , November 11, 2022
5/ 5stars
Exactly as shown. Wire connectors are unusually heavy gauge for the lower-amperage fuses (not exactly one-size-fits-all).
customer review - by , November 11, 2022
5/ 5stars
Exactly as shown. Wire connectors are unusually heavy gauge for the lower-amperage fuses (not exactly one-size-fits-all).
customer review - by , July 7, 2022
1/ 5stars
In line fuse
customer review - by , April 4, 2022
5/ 5stars
Good value and product
  »  
  »  
  »  
  »  
  »  
  »  

Parts Express Inline AGC Fuse Holder

stars Rating 5 | 15 reviews
Brand Parts Express
Shop more from PEX
UPC: 844632017322
SKU: PEX-070-609
Price:
$1.29Free shipping on orders over $129.00 on select PEX- items. Details
Buy in bulk & save 45% ($0.71 each)
Quantity:
718 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk
*  Price: $1.29 ea X 1 qty = $1.29
Quantity Price Save
1+ $1.29 0%
10+ $0.71 45%
* This item is excluded from use of other offer, discount or coupon.

Pricing Note

Free Shipping Promotion: Buy more items from the same series, product code beginning with PEX-, and you can get free shipping for an order of over  $129.00  consisting of only PEX- series products.

Product Description

Standard 1-1/4" fuseholder.

Overview:
Inline AGC Fuse Holder

Standard 1-1/4" fuseholder. Overall length 2-1/4" with 18 gauge wires.

Specification:



Manuals & Resources:

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item
Request More Information

Look Similar Items By Category

Electronics > Car & Vehicle Electronics > Car Electronics > Car Audio > Amplifiers
Automotive > Car Electronics & Accessories > Car Electronics > Car Audio > Amplifiers
Customer Reviews
5 out of 5
see all 15 reviews
5 stars
13
4 stars
1
3 stars
0
2 stars
0
1 stars
1
Write a Review
By AJS
Date: November 14, 2024
WARNING: THESE ARE DANGEROUS AND DO NOT BLOW WITH 5x THE CURRENT! This is a products liability/manufacturing defect case waiting to happen. The sole purpose of the fuse is to blow when the current is too high. Somehow I’m able to get 5 A through a 1 A fuse. A small amount of wiggle room is normal, but not 5x the current! The filament simply starts glowing red and heats up SIGNIFICANTLY. I tested my circuit before putting it in its casing, but if I didn’t there is no doubt in my mind that it would have melted the plastic after a few minutes. (I used the through-hole PCB clips, not the in-line component. )Less importantly, they arrived with the plastic box open, so every fuse spilled out and they were all mixed together in the plastic wrap. I was able to separate them myself, but that is a major pain. (And yes, I confirmed that the fuse I used above was, in fact, a 1 A fuse by the marking “F 1A L 250V”.)
Rating: 5 stars [5 of 5 Stars!]
By Edgar Babian
Date: August 04, 2024
Will work well for my wiring project
Rating: 5 stars [5 of 5 Stars!]
By talia
Date: April 21, 2024
Great value for the money!
Rating: 5 stars [5 of 5 Stars!]
By Fla Jeep Guy
Date: March 28, 2024
Quality Items for a Great Price !!
Rating: 5 stars [5 of 5 Stars!]
By Kota willson
Date: September 07, 2023
Wired it right into my harness, needed a peaceable link wire gauge was acceptable
Rating: 5 stars [5 of 5 Stars!]
By Michael McFarlane
Date: July 14, 2023
The fuses are in compartments and a table tells you the current rating. They are all mixed up so you can't figure out the correct size. They are not marked on the fuse either. The first fuse I used was open circuit even before I installed it. I needed a 1.5 amp fuse but they only had 2 amp fuses so I installed one. It lasted one dat then opened. It obviously wasn't a 2 amp rated fuse even though the cable on the box indicated that it was. I ended up installing a fuse labeled 15 amp even though the fuse link in it was very thin. You can't trust the fuse size chart on the box. The fuse holders were OK though.
Rating: 5 stars [5 of 5 Stars!]
Items 1 - 6 of 15 reviews
 1  2  3  [Next]