5 out of 5
Walton WTN18001 6 Pc Set Tap Extractors
* Click "Add to Cart" to calculate shipping and delivery time.
Product Description
Manufacturer Part Number: 18001
Remove broken taps in obscure places and save the threads.
Removes broken taps 3/16 - 5/8"
Remove broken taps without drilling, damaging threads, scrapping parts or having to use repair inserts.
Thehardened steel fingers fit in the flutes of a broken tap toback it out.
The WALTON Tap Extractor (holders, collars andsleeves) are guaranteed indefinitely against breakage. Allbroken holders, collars and sleeves will be replaced, without charge, when mailed directly back to Walton.
Fingers that become bent or broken or are too short forfurther use, can be purchased6 piece set contains sizes 3/16", 1/4", 5/16", 3/8", 7/16", 1/2"
Remove broken taps in obscure places and save the threads.
Removes broken taps 3/16 - 5/8"
Remove broken taps without drilling, damaging threads, scrapping parts or having to use repair inserts.
Thehardened steel fingers fit in the flutes of a broken tap toback it out.
The WALTON Tap Extractor (holders, collars andsleeves) are guaranteed indefinitely against breakage. Allbroken holders, collars and sleeves will be replaced, without charge, when mailed directly back to Walton.
Fingers that become bent or broken or are too short forfurther use, can be purchased
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Return Policy
All EAT- items are returnable, except for Open Box Scan Tools. scan tools/electronics, air tool are non-returnable
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category
Customer Reviews
By Deejay
Date: September 20, 2024
This did do the trick, but it was pretty twisted up trying to get into area I needed. Main thing is it worked!
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By James M. Cloninger
Date: June 21, 2024
High quality extractor with replaceable parts.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Michael in Woodbury MN
Date: June 21, 2024
Foolish me I buried an umbrella anchor in an 8” round 3’ deep hole and filled it with concrete. Only to find out the holes in the anchor plate did not line up with the umbrella base. It would have been an easy job to drill and tap new ones on a drill press. Much harder to do with a jury-rigged jig press. Four new holes, three of them tapped then [expletive deleted] the tap broke. I tried two “cheaper” options only to make things worse.Save your time and sanity and buy the right tool for the job.Oh, and check the holes on the plate before you dig the hole.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Ron
Date: May 09, 2024
Removed a troublesome tap from aluminum with ease.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Brian Bessette
Date: November 08, 2023
Easy to use
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Randy M Bienek
Date: September 14, 2023
Broke a tap a good 1/8 inch below the surface in a transmission. Broke 1 tab on the first try. Cut them to the same length and took my time setting the pin. Worked with a little bit of worry. Doubt the pins will last more than a few uses. Overall worth the cost.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]