5 out of 5
Walton WTN18001 6 Pc Set Tap Extractors
* Click "Add to Cart" to calculate shipping and delivery time.
Product Description
Manufacturer Part Number: 18001
Remove broken taps in obscure places and save the threads.
Removes broken taps 3/16 - 5/8"
Remove broken taps without drilling, damaging threads, scrapping parts or having to use repair inserts.
Thehardened steel fingers fit in the flutes of a broken tap toback it out.
The WALTON Tap Extractor (holders, collars andsleeves) are guaranteed indefinitely against breakage. Allbroken holders, collars and sleeves will be replaced, without charge, when mailed directly back to Walton.
Fingers that become bent or broken or are too short forfurther use, can be purchased6 piece set contains sizes 3/16", 1/4", 5/16", 3/8", 7/16", 1/2"
Remove broken taps in obscure places and save the threads.
Removes broken taps 3/16 - 5/8"
Remove broken taps without drilling, damaging threads, scrapping parts or having to use repair inserts.
Thehardened steel fingers fit in the flutes of a broken tap toback it out.
The WALTON Tap Extractor (holders, collars andsleeves) are guaranteed indefinitely against breakage. Allbroken holders, collars and sleeves will be replaced, without charge, when mailed directly back to Walton.
Fingers that become bent or broken or are too short forfurther use, can be purchased
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Return Policy
All EAT- items are returnable, except for Open Box Scan Tools. scan tools/electronics, air tool are non-returnable
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category
Customer Reviews
By Randy M Bienek
Date: September 14, 2023
Broke a tap a good 1/8 inch below the surface in a transmission. Broke 1 tab on the first try. Cut them to the same length and took my time setting the pin. Worked with a little bit of worry. Doubt the pins will last more than a few uses. Overall worth the cost.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By Jack Tusman
Date: July 08, 2023
I never do reviews BUT this tool worked better than I thought it could. I spent 4 hours trying to remove the broken tap and looked online and found this tool. It took 5 minutes to get the broken tap out. This tool worked so good I thought it was just slipping on the tap and when I removed the tool the broken tap was caught in the tool. This is the best tool ever for removing broken taps.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By Jack Tusman
Date: July 08, 2023
I never do reviews BUT this tool worked better than I thought it could. I spent 4 hours trying to remove the broken tap and looked online and found this tool. It took 5 minutes to get the broken tap out. This tool worked so good I thought it was just slipping on the tap and when I removed the tool the broken tap was caught in the tool. This is the best tool ever for removing broken taps.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By David Dodd
Date: June 28, 2023
Had my doubts, but worked great for me. Best technique was to make sure the shank was touching the body of the broken tap, rock it back and forth (don't go nuts on the torque!), and tap stub will loosen up, and then back it out and Bob's your uncle!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By A Customer
Date: June 02, 2023
It did a great job on broken a 1/2 tap. The tap was hanging up a bit but after I ground down the uneven points of the tap it went a lot better.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By A Customer
Date: November 07, 2022
The tip of the tap was wedged in tight. I followed the directions - cleaned the chips out of the grooves with a dental pick and compressed air, applied cutting oil, then inserted the fingers as far as I could, which was about an 1/8 inch. I secured the sleeve until it contacted the surface, lightly tapped it with a hammer and punch to get it snug. I tried turning it both ways, also applying downward pressure until the fingers bent and then slipped out. Ground off the bent finger tips, tried again. Third attempt it freed up and came out! Much easier than other methods I've used.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]