0 reviews
Be the first to review this item!
Shoe Goo Shoe Repair Adhesive and Protective Coating 1.0 Fl Oz, Price/6
Shop by themes: Shoes and Accessories
* Click "Add to Cart" to calculate shipping and delivery time.
Product Description
Price is for 6.
Shoe GOO is the #1 shoe repair adhesive! It's ideal for fixing worn soles or damaged heels, coating shoes to prevent premature wear and sealing galoshes, waders or rubber boots. The unique formula is designed for strong abrasion resistance and better adhesion to flexible materials.
WARNING: This product can expose you to chemicals including toluene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.INSTRUCTIONS:
Follow these step-by-step directions when using Shoe GOO:
DIRECTIONS – Read directions and test small area before use.
TECHNICAL DATA SHEET
SG TDS USA AU NZ CAN _REV 13 (English)
- Bonds, protects and rebuilds for a permanent repair
- Excellent sealant-perfect for patching small holes
- Waterproof-bond remains secure even when exposed to water
- Creates extra traction-can even be used on skateboards!
WARNING: This product can expose you to chemicals including toluene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.INSTRUCTIONS: INSTRUCTIONS
Follow these step-by-step directions when using Shoe GOO:
DIRECTIONS – Read directions and test small area before use.
- Surface should be clean, dry and free of dirt.
- Puncture seal in neck of tube using pointer cap. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from -40 to 180 °F (-40 to 82 °C) intermittently.
- Apply directly to surfaces to be protected, bonded or repaired. For waterproofing and protecting, use thin coats (spread with a disposable tool) to build a thick coating, allowing each layer to set 3-4 hours.
- Allow repair to cure for 24 hours. Depending on materials and temperature, maximum strength may not be reached for 48 to 72 hours.
- For future easy cap removal, apply a thin coat of petroleum jelly to the threads of the tube before replacing the cap.
- Clean uncured adhesive with acetone or citrus-based solvents. Cured material may be removed by cutting or scraping.
DATA SHEETS
SAFETY DATA SHEET SDS SHEET REQUESTS: To request an SDS, please use the below link and include the following information
|
TECHNICAL DATA SHEET
SG TDS USA AU NZ CAN _REV 13 (English)
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Product FAQ
How long does SHOE GOO take to cure?
A full cure takes 24 to 72 hours, depending on the surrounding environment. With lower temperatures and higher humidity, cure time increases; with higher temperatures, cure time decreases. To speed drying time, apply heat using a handheld dryer set on low. Hold dryer at least 6 inches from the surface.
How can SHOE GOO be cleaned up?
Small amounts of acetone or citrus-based solvents may be used on uncured adhesive; the adhesive will ball up and brush off. Cured adhesive may be removed by cutting or scraping.
Is SHOE GOO water resistant?
Yes. It is water resistant immediately upon application. Apply SHOE GOO directly to the surface to be sealed. Use thin coats of SHOE GOO to build a thick coating on the surface to be sealed, allowing each layer to set 3 to 4 hours. SHOE GOO hardens by solvent evaporation, so allow time for thorough hardening to ensure proper bonding and wear resistance.
What temperature range does SHOE GOO withstand?
Once cured, SHOE GOO will withstand temperatures between -40 °F and 150 °F (-40 °C to 66 °C).
A full cure takes 24 to 72 hours, depending on the surrounding environment. With lower temperatures and higher humidity, cure time increases; with higher temperatures, cure time decreases. To speed drying time, apply heat using a handheld dryer set on low. Hold dryer at least 6 inches from the surface.
How can SHOE GOO be cleaned up?
Small amounts of acetone or citrus-based solvents may be used on uncured adhesive; the adhesive will ball up and brush off. Cured adhesive may be removed by cutting or scraping.
Is SHOE GOO water resistant?
Yes. It is water resistant immediately upon application. Apply SHOE GOO directly to the surface to be sealed. Use thin coats of SHOE GOO to build a thick coating on the surface to be sealed, allowing each layer to set 3 to 4 hours. SHOE GOO hardens by solvent evaporation, so allow time for thorough hardening to ensure proper bonding and wear resistance.
What temperature range does SHOE GOO withstand?
Once cured, SHOE GOO will withstand temperatures between -40 °F and 150 °F (-40 °C to 66 °C).
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item