Cheap as chips and fixed my little Peavey...

Despite the small size this tank worked and sounded suprisingly good.

Plugged it in. Worked first time. Thank you. No more dry amp sound!

Shorter pan than the original but it works great in my old peavey.

Less than 5 minutes, replaced the old non op unit and reverb is perfect. The fit was exact, reverb sound quality is just right. Very happy. Great value.

1982 Peavey Backstage 20 - old pan faded away amp; died. Got this one which replaced the old 4EB2C1B perfectly. Was concerned that footprint might be smaller - or - 2 springs vs 3, but can confirm: works great, plenty of splash on tap, and very useable range with full rotation of knob. Total winner, would recommend.

perfect easy fit for 90s blues jr. very responsive. Great deal

I used this to replace a broken reverb on Peavy Blazer. I followed a YouTube video to modify it properly to connect to the amp, and it works nicely. It's very good for the price. This may be an issue with the Peavy, but the reverb only seems to work between 6 and 10 on the dial. The sound is full and pleasant, with a traditional spring reverb sound, and the decay can go pretty long, with the mix creating some big atmospheric tones.

Easy to install, works perfectly!

Works great, just swapped right in for old, rusted tank. Connect, screw down and you are all set. Great value for the money. No need to spend more.

This is a junk reverb tank that is not listed properly for fit. Be careful should you purchase it

I have an older Fender blues jr and my reverb tank went out (a very common thing).Honestly, I wasn't expecting how good a replacement it would be.It it better than the original equipment and has a great vintage spring sound.$25 is a no brainer

Ready to go out of the box with easy installation.

Used to replace solid state Peavey tank. Sounded great! Client was thrilled! Bought a second unit to keep around for a future repair

I was looking for a new tank for my Doepfer A-199 spring reverb module. IMO, it's always had too high of a base frequency (makes it sound like the reverb is in a tiny room), and the output level of the reverb always seemed too low.I saw this tank, which has springs that are almost twice as long, and the same RCA connections, and decided to give it a go. The base frequency is much lower (like it's reverb in a big room or hall), and the output is much hotter, which makes it easier to mix back in. Also, the reverb is much more full, which gives more room to scoop out high/low frequencies with a VCF, etc.I would highly recommend this to anyone looking for a new flavor of reverb for their Eurorack spring reverb module, especially the Doepfer A-199.

I bought this item to replace a 4AB3C1B Accutronics reverb tank in my Fender Twin Amp (ProTube series). The Accutronics tank was working, but it wasn't producing as much reverb as it should have been and had begun to feed back if I set the reverb at 7 or higher.This MOD tank sounds far better than the Accutronics tank I replaced. It sounds a lot like the old Accutronics reverb tanks that were made before the company started producing junk. It produces a much smoother sound than current Accutronics tanks.This tank has a far more reverb at any given setting when compared to a current Accurtronics tank, so I find that setting it to 4 is about like setting the old tank to 7. If you set this tank at 7, it sounds like a good working Accutronics tank maxed out. If you max out this tank, it produces more reverb than you probably want.Construction of this item is a little better than that of the tank I replaced. It is the same size as the same model Accutronics tank it. There are 4 clear rubbery feet/mounts that isolate the tank from the amp. Also, when you move this tank around, the springs don't slap the metal quite as easily as with the stock tank.The item was packed in bubble wrap with foam blocks above and below the springs to keep it from slapping around in shipping.I highly suggest using this reverb tank.

Finally, a reverb tank that's built like, uh, a tank. I dropped it after playing through it the first time and thought it was done for--smacked the concrete hard enough to bend one corner of the chassis back at a 90-degree angle. Turns out it was fine. Definitely a sign of high quality parts built into a sturdy enclosure. In terms of sound, it works great with my Fender Twin Reverb. Mine is early silverface, but from what I've heard this model fits all Twin Reverbs, even the reissues. The effect is pretty lush and deep when dimed, but it stays surfy. EQ things right and you can get a pretty perfect, washed out trail behind your playing without losing your notes.

High-quality unit. Very cavernous-sounding - long reverb tails. Not exactly the sound I'm after, but if that's what you're looking for, here it is.

I'm happy with this product.I had trouble with the old reverb tank off and on since I bought the amp new.I've had this in for over a month and it has been hanging in like a trooper.It sounds very much like the part i replaced only more dependable.Good job

After two accutronics tanks failed on me fairly quickly I decided to give this a try. Reverb sounds great in my Pro Reverb and it looks like the design is an improvement and less likely to fail. So far, so good.