skip to footer block
HAK Century HSQ165 Centurion Pro Motor 1.65 Thp P15160709HAK-CRMHSQ165 https://cdnimages.opentip.com/full/HAK/HAK-CRMHSQ165.jpg Century HSQ165 Centurion Pro Motor 1.65 Thp Manufacturer Part Number: HSQ165Part #: CRMHSQ165MFG #: HSQ165Century (A.O.Smith) Centurion Pro Motors - Square Flange - 1.65 THP Features and Benefits: Replaces SQ1102 & USQ1152 The Centurion Pro design packs best-in-class features into a rugged, accessible layout that improves the installation experience Features a NEW Hybrid end frame design, PCB terminal board, voltage change device and definitive shaft access (7/16\" wrench) THP equals the Total Output (HP x service factor) and the replacement motor must equal or exceed motor being replaced 48Y Frame Brand: CenturyPart Number: CRMHSQ165 Regal_HSQ095_specification_sheets (361.89 kB) 15160709 23.0000lbs 9.00 9.50 17.50
Century
319.2800 2026-08-24 87 In Stock
customer review - by , November 11, 2024
5/ 5stars
This motor seems a little longer than the original. However, the mounting lined right up. I replaced the shaft seal, slinger, impeller, and o rings as well. Since you already have the whole pump taken apart, go ahead and replace everything that you can. This motor is super quiet. I use it on a filter to run a waterfall on a large koi pond, so the pond water wears out motors quicker than a swimming pool would. The price was almost half of what it would have cost to buy locally. So far so good.
customer review - by , September 9, 2024
5/ 5stars
Worked great. All parts there
customer review - by , June 6, 2024
5/ 5stars
had what they say
customer review - by , June 6, 2024
5/ 5stars
I bought this one as a spare!
customer review - by , May 5, 2024
5/ 5stars
This motor fit my flotec pump perfectly! If you also get the pump rebuilt kit you should know that the rubber washer that goes onto the motor shaft is already on the new motor. (At least it was on mine)
customer review - by , February 2, 2024
5/ 5stars
I have a 40 year old Sta-Rite old pump, and the old motor after 20 years burned up. Could not be happier to have water again! Buy the gaskets/pump seal kit if available - I have a small leak, and will have to redo some work - but I can't complain about not having water!
customer review - by , January 1, 2024
5/ 5stars
I bought this to replace a older motor on my pool pump. This was the exact part I needed. If you order this make sure it is exactly what you need.
customer review - by , May 5, 2023
1/ 5stars
Works like a charm!

Century HSQ165 Centurion Pro Motor - 1.65 Thp, Price/each

stars Rating 4.5 | 8 reviews
Brand Century
Shop more from HAK

SKU: HAK-CRMHSQ165
Price: $319.28
Quantity:
87 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Product Description

Price is for each.

Manufacturer Part Number: HSQ165

Part #: CRMHSQ165

MFG #: HSQ165

Century (A.O.Smith) Centurion Pro Motors - Square Flange - 1.65 THP


Features and Benefits:

  • Replaces SQ1102 & USQ1152
  • The Centurion Pro design packs best-in-class features into a rugged, accessible layout that improves the installation experience
  • Features a NEW Hybrid end frame design, PCB terminal board, voltage change device and definitive shaft access (7/16" wrench)
  • THP equals the Total Output (HP x service factor) and the replacement motor must equal or exceed motor being replaced
  • 48Y Frame


Brand: Century

Part Number: CRMHSQ165

Century HSQ165 Centurion Pro Motor - 1.65 Thp Regal_HSQ095_specification_sheets (361.89 kB)

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.

Specifications

Need more information?
Our staff are available to answer any questions you may have about this item


Customer Reviews
4.5 out of 5
5 stars
7
4 stars
0
3 stars
0
2 stars
0
1 stars
1
By Mark G.
Date: November 25, 2024
This motor seems a little longer than the original. However, the mounting lined right up. I replaced the shaft seal, slinger, impeller, and o rings as well. Since you already have the whole pump taken apart, go ahead and replace everything that you can. This motor is super quiet. I use it on a filter to run a waterfall on a large koi pond, so the pond water wears out motors quicker than a swimming pool would. The price was almost half of what it would have cost to buy locally. So far so good.
Rating: 5 stars [5 of 5 Stars!]
By Joseph
Date: September 05, 2024
Worked great. All parts there
Rating: 5 stars [5 of 5 Stars!]
By Discover
Date: June 15, 2024
had what they say
Rating: 5 stars [5 of 5 Stars!]
By Lisa Margaret Webb
Date: June 14, 2024
I bought this one as a spare!
Rating: 5 stars [5 of 5 Stars!]
By dcon0700
Date: May 09, 2024
This motor fit my flotec pump perfectly! If you also get the pump rebuilt kit you should know that the rubber washer that goes onto the motor shaft is already on the new motor. (At least it was on mine)
Rating: 5 stars [5 of 5 Stars!]
By Harry Lisle
Date: February 19, 2024
I have a 40 year old Sta-Rite old pump, and the old motor after 20 years burned up. Could not be happier to have water again! Buy the gaskets/pump seal kit if available - I have a small leak, and will have to redo some work - but I can't complain about not having water!
Rating: 5 stars [5 of 5 Stars!]
Items 1 - 6 of 8 reviews
 1  2  [Next]