skip to footer block
SPF Balboa Water Group 30408 Pressure Switch 1/8In Npt 3A Spst 0 2 Psi Balboa P15445456SPF-BB30408 https://cdnimages.opentip.com/full/SPF/SPF-BB30408.jpg Balboa Water Group 30408 Pressure Switch 1/8In Npt 3A Spst 0 2 Psi Balboa Manufacturer Part Number: 30408Pressure Switch 1/8\" Npt 3ASpst 0-2 Psi BalboaFeatures. This Single Pull Single Throw (SPST) Pressure Switch for Spa Heaters is a 3 Amp. Switch for a 1/8 in. hole. With a 3/8 in. stainless steel thread. 2.0 PSI. 15445456 0.2100lbs 0.00 0.00 0.00
Balboa Water Group
66.4900 2026-08-24 19 In Stock
customer review - by , March 3, 2025
5/ 5stars
This replacement worked for my older Catalina Spa. While the pressure switch I replaced called for 0.5-5.0 psi, this pressure switch rated at 2.0 psi has worked for me. It appears that my spa runs a bit more often with this new switch, perhaps heating up the spa immediately when it drops below 103 degrees (as set) instead of waiting until the spa drops down a larger amount of temperature. When my next power bill comes, I’ll have a better idea of whether this change caused more power use. Besides being located in an inconvenient spot, replacing it was easy with a 1/2” open end wrench and some teflon tape.
customer review - by , August 8, 2024
5/ 5stars
Fit perfect and works great
customer review - by , July 7, 2024
5/ 5stars
Finally fixed my hot tub! Easy to install and not a bad price!
customer review - by , June 6, 2024
5/ 5stars
This switch worked perfectly to replace my Balboa 30408 2psi 3amp pressure switch that was faulty and cause g a FLO error.
customer review - by , December 12, 2023
5/ 5stars
I bought this thing for my Catalina Spa that had a FLO reading on the panel. Heater wouldn’t turn on. I wasn’t positive this would fix it but i took the plunge. Get it? Installation was straightforward except for the location of this part on my spa which was on the back side of the pipe leading from the heater. I unthreaded the old one, added teflon tape to the new one and threaded it in. The only thing I’m not sure about was the thread pitch. The new one was a little stiff turning it in. Could be too much teflon tape. It went in enough that i feel confident that it won’t leak and so far (6 Months) it hasn’t. Turned the hot tub back on and voila, it worked. Nice product.
customer review - by , June 6, 2023
5/ 5stars
Perfect

Balboa Water Group 30408 Pressure Switch 1/8In Npt 3A Spst 0-2 Psi Balboa, Price/each

stars Rating 5 | 6 reviews
Shop more from SPF

SKU: SPF-BB30408
Price: $66.49
Quantity:
19 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Product Description

Price is for each.

Manufacturer Part Number: 30408

Pressure Switch 1/8" Npt 3A
Spst 0-2 Psi Balboa

Features. This Single Pull Single Throw (SPST) Pressure Switch for Spa Heaters is a 3 Amp. Switch for a 1/8 in. hole. With a 3/8 in. stainless steel thread. 2.0 PSI.

Balboa Water Group 30408 Pressure Switch 1/8In Npt 3A Spst 0-2 Psi Balboa

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.

Specifications

Return Policy

Used items cannot be returned.
Need more information?
Our staff are available to answer any questions you may have about this item


Look Similar Items By Category


Customer Reviews
5 out of 5
5 stars
6
4 stars
0
3 stars
0
2 stars
0
1 stars
0
By A Customer
Date: March 26, 2025
This replacement worked for my older Catalina Spa. While the pressure switch I replaced called for 0.5-5.0 psi, this pressure switch rated at 2.0 psi has worked for me. It appears that my spa runs a bit more often with this new switch, perhaps heating up the spa immediately when it drops below 103 degrees (as set) instead of waiting until the spa drops down a larger amount of temperature. When my next power bill comes, I’ll have a better idea of whether this change caused more power use. Besides being located in an inconvenient spot, replacing it was easy with a 1/2” open end wrench and some teflon tape.
Rating: 5 stars [5 of 5 Stars!]
By Ed
Date: August 02, 2024
Fit perfect and works great
Rating: 5 stars [5 of 5 Stars!]
By Shawn M. Walker
Date: July 24, 2024
Finally fixed my hot tub! Easy to install and not a bad price!
Rating: 5 stars [5 of 5 Stars!]
By CJ
Date: June 07, 2024
This switch worked perfectly to replace my Balboa 30408 2psi 3amp pressure switch that was faulty and cause g a FLO error.
Rating: 5 stars [5 of 5 Stars!]
By W C.
Date: December 29, 2023
I bought this thing for my Catalina Spa that had a FLO reading on the panel. Heater wouldn’t turn on. I wasn’t positive this would fix it but i took the plunge. Get it? Installation was straightforward except for the location of this part on my spa which was on the back side of the pipe leading from the heater. I unthreaded the old one, added teflon tape to the new one and threaded it in. The only thing I’m not sure about was the thread pitch. The new one was a little stiff turning it in. Could be too much teflon tape. It went in enough that i feel confident that it won’t leak and so far (6 Months) it hasn’t. Turned the hot tub back on and voila, it worked. Nice product.
Rating: 5 stars [5 of 5 Stars!]
By A Customer
Date: June 24, 2023
Perfect
Rating: 5 stars [5 of 5 Stars!]
Items 1 - 6 of 6 reviews
 1