This product organized my biggest storage nightmare. It is super sturdy and worth every penny. It quickly was delivered,

This product wasnt assembled correctly, it wasnt square. My carpenter took an entire day adding shims until it finally worked.

Honestly they're a waste of your time. A lot of unnecessary steps and it's not clear on everything. However I love the drawer despite it being annoying to install. It is great quality and I do recommend it

This is the perfect solution to a narrow cabinet that is only good for baking pans or cutting boards. The carpenter installed it quickly towards the end of the remodel. It is sturdy, attractive, well designed. It glides smoothly and soundlessly. For my needs I removed the (easily removable) center support and it works better for me that way.

It fit to my kitchen

Easy to shop with this seller! Description was very detailed that we got the exact size we needed! Great quality and has soft close too.

I had a small space - 6 inches wide - to fill by the oven and this worked great. The template provided made it a breeze to install. Very sturdy. I'm happy and look forward to long use.

Nice product. Well built. Limited sizes.My face-framed cabinet opening is exactly 7 wide. For sure the 8 unit was too large. 5 would be a space-waster.The new 6 was close to convincing; but it did demand a bit more than my available 7.This is where their very well presented engineered specification page comes in: Clearly indicating that with a bit of careful trimming along a small area of the vertical face framing left and right, a 7-1/4 minimum demand requirement could be achieved. Go to their engineering drawings.

Construction is excellent. It was just alot smaller than expected. The middle bar really impedes storage.

Works just like it is supposed to.

This is solidly built hardware that works well and I expect to work for years to come, if a little expensive. My ONLY real challenge is with the instructions. While the list of things you need to have includes a 3/32 drill bit, it very clearly, in two places, says to use a 5/32 drill bit. Unfortunately if (like me) you followed the instructions (which included a great template to make sure you drilled the holes in just the right spot) you now have holes way too big for the included screws. I had to go to the hardware store to find bigger screws. Also shorter screws because the included 3/4 screws would have stuck out the bottom of my cabinets. With the larger screws this now works beautifully.

Pros:- Nice upgrade- Well designed, sturdy- Good fitCons:- Instructions were not clear about how to detach top part from slider bottom. Eventually I figured it out. There are 3 plastic tabs you need to press. The center one first and then the 2 on the sides at the same time.- Flimsy box has a hole and I was missing a nut. Easy to find replacement.- Instructions did not say how to put the metal rack back onto the slider base. If are not careful it can get out of alignment. Also the blue pastic stops in the back can come loose and jamb the unit from closing.

Makes accessing our cutting boards so much easier! Love it!

We were using a 9 inch cabinet to store all of our sheet pans. We added this 5 inch pull out to complement a spice rack we had on the other side of the cooktop. Once added we could no longer fit about half of our trays in the cabinet. So much of the space becomes wasted. The item it's self is easy enough to assemble and sturdy. It is just not functional.

This item is exactly what we needed for a skinny cabinet in our kitchen layout. My husband [who can fix everything, IMO] read the directions fully and got everything set up to install. It was a nightmare. A 30 min project turned into 3 hours. After all was done, the soft close worked twice and quit. Now to open it is like pulling a 30 lb weight. We're surmising the soft close failure is the explanation of the heaviness in opening. A project he isn't too excited to return to. But someday...

The product is every bit as well built as other reviews claim -- you get what you pay for in that regard. And they did think of a lot of details, though not every detail. So once it gets from the box to a finished installation, you will be happy. The problem is that little matter of installing it. I was fortunate enough to install mine in an island before the countertop was installed. I have no idea how you would do it otherwise, but let's disregard that for now. The 30 minute installation is a bit of a joke. Unless you've done it before, count on at least three hours.The product arrives with the business end attached to the sliding base. So your first job is to detach the latter from the former. They provide some unclear instructions for how to do this. It is vaguely similar to removing drawers with ball bearing slides, but more difficult. The latches are much more difficult to find and manipulate. If, like me, you have to remove it again after installation (more in a moment), forget about it. Just remove the whole unit in that case.So figure on 45 minutes and some sore fingers just to disassemble the top from the bottom. Once you succeed, it's time to install the bottom in the cabinet. They do provide a template, which is helpful. Take your time to get it positioned straight and properly, then mark your holes. Remove the template, drill the front holes and install the two front screws. In my case that was difficult because the screws were missing. No big deal, if like me you're a pack rat and have a hardware store in your garage. Anyway, when you're done with the front, recheck for straightness, then drill and install the two back screws.The next step is difficult and I messed it up. It's time to slide the top onto the base that you just installed. And it has to be right. In my case I did not engage the middle slider properly, and the unit didn't slide properly. After much fiddling, I realized that I needed to disassemble the top from the base and try again. Unfortunately, this is next to impossible. Much easier to pull the top out as far as it will go, then remove the four base screws that you installed, and then work with the unit outside of the cabinet. Once you resolve the slider situation (if you had a slider situation), just reinstall it.Once the unit is installed and sliding properly, you can set the stops in the back that prevent the unit from sliding out too far. And they also give you guides, which install on the inner face of the cabinet opening. Nice touches, don't neglect them.If all is well, you can install the cabinet door. This is easy in principle, but it is very difficult in practice to get it exact. They do provide adjustments in the Z direction (into the front plane of the cabinet). But it is very hard to adjust in the X and Y axes. So, basically, take your time and drill the holes in the cabinet door carefully because you only get one shot (well, technically I guess you could get two by turning the door upside down).If you have not bought the unit, I would mention two other issues that are not issues with the product, but issues with my own planning. First, if you plan to install one of these things, order a door without hinges. It's a waste, and visually unappealing, to have a door with hinge installation sockets on the inside face. Second, it's a shame in general to have to install a 5 unit into a 9 cabinet. So, again, choose your cabinet geometry carefully ahead of time. In the end, this is a very well-built product that you won't regret owning. But plan ahead on the cabinet design, and plan on a challenging installation.

Works great you will loose some storage space for the convenience of being able to pull out. All in all is very sturdy. Can take some time to install and prep and I build things for a living. Was missing a few mounting screws which was not a problem for me as I have extras laying around.

Love all rev a shelf units. Always tricky to install but so worth it. I remodeled my kitchen and had my contractor out this in for me

My husband out this together but it was very time consuming and he's a pretty experienced handy man. If I had to do it, it would have been a total fail. Very sturdy though. Think it was a bit pricey, but it was actually cheaper than our local hardware store by just a few bucks. Love being able to easily access the cookie sheets, etc.

I paid $180 when I bought this. It works well, and made a nearly useless part of my cabinmates usable for some baking sheets, and rolls of aluminum foil and other items. It is over all very sturdy, and has held up well. The installation was easy, but the included instructions were lacking. The only thing that keeps this from 5 stars is the price. At $120 I would have felt like this was worth every penny.