5 out of 5
Customer Reviews
By
cliff
Date: November 07, 2025
I used this and it worked great I did 50 holes.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
iJoel H
Date: August 14, 2025
Worth to keep when needed If you are on firearm building.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
WGI
Date: April 02, 2025
I really didn't think about what the quality of a 20$ reamer would be compared to the other cheapest which was $50. I really hope the picture quality is as good as it was when I took it through a lens.. If it's not, the cutting edge has been ground with what looks like an asphalt wheel. I could be wrong about this, but, I think when they cut the reamer they do so at an ever so slight angle so its not the same width the whole length of cut. The tip is smaller and then gets slightly wider. This is the opposite, the tip of the reamer measures at .2435 (bought it as .2430- so its already oversize) the end of the cut measures at .2425". Moral of story- if you need a finishing reamer to finish a hole... buy one that's a but more money. It's also not new, its a recycled reamer, not sure if its even straight.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
ERM
Date: December 26, 2024
Worked perfectly.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Brendon B.
Date: December 22, 2024
Began reaming ok, but a bit of binding and it bent immediately without much force.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: August 17, 2024
Works as it should A.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
dcfolsom
Date: July 17, 2024
I use this to ream the necks of any case that uses .308 projectiles. With all trimmed to same length after sizing, reamed to .306 and finished with a factory-crimp die, neck tension is consistent and groups as tight as I can get them. Also have a .2620 that I use for 6.5cm/.264
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Frank Nickel
Date: July 09, 2024
I needed this to make a tool for adjusting the shifter fork spacing on a Harley 4 speed transmission.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jarrett M. Weatherspoon III
Date: February 12, 2024
Arrived quickly and as advertised.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
JR
Date: January 18, 2024
This .505 reamer measures correct per my micrometer and works well. I have only used it on soft brass so I can't comment on it's durability on hard metals.It didn't matter to me, but note that this .505 reamer is a bright steel finish, not black oxide as some of the photos make it appear.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Grimrin
Date: November 15, 2023
Quick delivery and made perfect hopes. I'm happy with this tool.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Roxanne E
Date: April 24, 2023
Item as stated
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Fastbugs
Date: February 19, 2023
good deal
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Larry
Date: December 12, 2022
No complaints.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Ilia
Date: June 07, 2022
I bought a 0.5540 reamer and it cuts exactly to the specified diameter.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Dave J.
Date: June 04, 2022
Bought this reamer to complete a project I had started, it worked well, project completed!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Me
Date: May 25, 2022
No shaft size listed and the 11/16 will not fit in a 1/2 inch chuck. I'll probably be returning it.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Woodsrider
Date: April 20, 2022
Works just as intended
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
lauren r gibbs jr
Date: March 24, 2022
Worked as intended. If I did over, would order it with a 1/2 shank to fit a drill. Otherwise it did its job.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
john long
Date: January 20, 2022
This Worked great, I used it in 304 stainless steel, it put a nice reamed hole, tolerance was spot on
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]