5 out of 5
Customer Reviews
By
iJoel H
Date: November 14, 2025
Worth to keep when needed If you are on firearm building.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
WGI
Date: June 25, 2025
I really didn't think about what the quality of a 20$ reamer would be compared to the other cheapest which was $50. I really hope the picture quality is as good as it was when I took it through a lens.. If it's not, the cutting edge has been ground with what looks like an asphalt wheel. I could be wrong about this, but, I think when they cut the reamer they do so at an ever so slight angle so its not the same width the whole length of cut. The tip is smaller and then gets slightly wider. This is the opposite, the tip of the reamer measures at .2435 (bought it as .2430- so its already oversize) the end of the cut measures at .2425". Moral of story- if you need a finishing reamer to finish a hole... buy one that's a but more money. It's also not new, its a recycled reamer, not sure if its even straight.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
ERM
Date: March 15, 2025
Worked perfectly.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Brendon B.
Date: March 11, 2025
Began reaming ok, but a bit of binding and it bent immediately without much force.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: October 29, 2024
Works as it should A.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
dcfolsom
Date: September 26, 2024
I use this to ream the necks of any case that uses .308 projectiles. With all trimmed to same length after sizing, reamed to .306 and finished with a factory-crimp die, neck tension is consistent and groups as tight as I can get them. Also have a .2620 that I use for 6.5cm/.264
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Frank Nickel
Date: September 18, 2024
I needed this to make a tool for adjusting the shifter fork spacing on a Harley 4 speed transmission.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Jarrett M. Weatherspoon III
Date: April 14, 2024
Arrived quickly and as advertised.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
JR
Date: March 19, 2024
This .505 reamer measures correct per my micrometer and works well. I have only used it on soft brass so I can't comment on it's durability on hard metals.It didn't matter to me, but note that this .505 reamer is a bright steel finish, not black oxide as some of the photos make it appear.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Grimrin
Date: January 12, 2024
Quick delivery and made perfect hopes. I'm happy with this tool.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Roxanne E
Date: June 10, 2023
Item as stated
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Fastbugs
Date: April 04, 2023
good deal
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Larry
Date: January 21, 2023
No complaints.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Ilia
Date: July 07, 2022
I bought a 0.5540 reamer and it cuts exactly to the specified diameter.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Dave J.
Date: July 04, 2022
Bought this reamer to complete a project I had started, it worked well, project completed!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Me
Date: June 24, 2022
No shaft size listed and the 11/16 will not fit in a 1/2 inch chuck. I'll probably be returning it.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Woodsrider
Date: May 18, 2022
Works just as intended
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
lauren r gibbs jr
Date: April 19, 2022
Worked as intended. If I did over, would order it with a 1/2 shank to fit a drill. Otherwise it did its job.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
john long
Date: February 12, 2022
This Worked great, I used it in 304 stainless steel, it put a nice reamed hole, tolerance was spot on
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Roger
Date: January 05, 2022
I received the reamer quickly and it was just what I needed
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]