4.5 out of 5
Customer Reviews
By
John Smith
Date: December 09, 2025
Requires Teflon tape around the threads. Hence, 4 stars.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]
By
Russell A. Shreve
Date: November 24, 2025
Does what it says, measure before you order!!
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By
M Surf
Date: October 22, 2025
Fit my Tundra to hook up the pressure bleeder. Worked great and no leaks.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Rusherton
Date: September 02, 2025
It fit a Lexus gx470 as it was meant for. No leaks and it held pressure
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
A Customer
Date: May 18, 2025
Used this to bleed brakes on my 1993 Toyota Land Cruiser, worked great
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Cletis Johnson
Date: May 01, 2025
Used it to flush the brakes on a 2011 Toyota Prius along with a Motive Products Power Bleeder that I bought over 10 years ago and it worked GREAT ! It took about 20 minutes.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
David Porter
Date: November 19, 2024
Perfect fit on a 2010 Toyota Tundra. The product needed some slight modifications to fit on my Motive power bleeder. I added a quick disconnect and it works like a charm.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Eric
Date: September 06, 2024
This adapter clips onto the master cylinder of my Toyota (make sure it's the right size for you) and lets you put pressurized air into the master cylinder reservoir, thus making it a lot easier to bleed brakes. Instead of having to pump-hold-bleed conventionally, you can just apply pressure, crack open the bleed screw, and it's done.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
Vicky zhang
Date: May 14, 2024
It is very easy to use and get my job done fast, still pricey to me, will recommend.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
MY303V8
Date: April 08, 2024
Plugs right into the Orion Bleeder kit, seals perfectly, no leaks, ready to bleed the brakes with ease.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
kaleb michael
Date: March 27, 2024
Worked perfectly, so nice!!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
andy standifer
Date: December 12, 2023
Perfect for bleeding brakes on lexus/toyota, used with motive bleeder.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Sonny Crockett
Date: October 20, 2023
I use this with a power bleeder. I did modify this with a nicer NPT fitting and I had to buy an additional NPT fitting and hose to connect it to my bleeder. Not a big deal. It snaps onto the factory master cylinder reservoir with ease and it held 15psi with no leaks at all. Perfect addition to my tool chest. It is pricey, but still cheaper than having a shop do it. You will be more likely to change the fluid more often simply because you CAN.
Rating: [4 of 5 Stars!]
[4 of 5 Stars!]
By
AlejandroMagno
Date: June 23, 2023
The product I've been waiting for! This worked perfectly for standard sized hand pump brake bleeder. I own the Schwaben one, ( which is really a rebranded one) I own both Euro and Asian vehicles and wanted adapter that fit my existing Schwaben brake bleeder. This item worked flawlessly with a 2015 Rav 4 AWD. LE No mess, pumped up to 15 PSI and held perfectly! Thanks for making this, I am satisfied with the result!
Rating: 
[1 of 5 Stars!]
[1 of 5 Stars!]
By
Chris
Date: June 20, 2023
I tested for leaks with no fluid in the bleeder and it held pressure. I then added fluid and pumped it up to 12psi. While I was bleeding my rear brakes, the fluid must've eaten through the small amount of thread locker and created a pinhole leak. Fluid sprayed out for a few minutes before I saw it, making a huge mess. I pulled the fitting off and found that the threads on both the fitting and the manifold were very low quality and very loose. I used first used 3 layers of Blue Monster teflon tape (which is fairly thick) and it was still too loose to seal. I then tried 6 layers with still wasn't very tight but it was tight enough to stop the leak. To anyone that gets one of these and uses it, make sure to drape shop towel over it to contain the fluid if it develops a leak! You'll save a lot of cleanup time.
Rating: [1 of 5 Stars!]
[1 of 5 Stars!]
By
Kevin
Date: June 14, 2023
Great brake bleed adapter. High quality machined parts make a much better seal to the master cylinder on my Toyota than a cheap plastic bleed adapter. I had to change the quick disconnect on it to work with my power bleeder but otherwise it works great.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Errol L.
Date: June 08, 2023
cost is high, plus need another item to make this adapter to work, when i can just buy a bottle fluid filler that clips on the master cylinder and keeps master cylinder filled.
Rating: 
[2 of 5 Stars!]
[2 of 5 Stars!]
By
P. Jones
Date: April 01, 2023
I have been using my own one way airline valve on a bottle at the caliper to bleed the brakes. The weakness was on the brake pedal upstroke some air could get in at the threads of the bleed screw. I wanted to switch to pressurizing the reservoir but did not have a clean solution. This item is the clean solution. It fits the reservoir perfectly. It comes with an unfamiliar connector that OMtool uses. It is a standard 1/4" threaded hole so I just removed that fitting and inserted an industrial style 1/4" fitting. To bleed I just remove the old fluid from the reservoir and refill with clean fluid. Cap it with this device and hook up my compressor line set to 15lbs. Follow the standard bleeding process at each wheel. Keep an eye on the reservoir and refill if necessary
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
J. J. Izzo
Date: March 24, 2023
Pressure bleeder adapters can be hard to come by for many Toyota models due to what's essentially a friction-fit cap design versus other manufactures' varying screw-on types. That's my way of saying, if you have a Motive pressure bleeder like I do, you'll need to look at other company's adapters to pair with it. Luckily, this CMTOOL adapter was perfect for my needs. We're currently a Toyota / Lexus household, and it has worked perfectly for both on multiple occasions! This adapter got the job done once I fit it up with the necessary hose and fitting to mate to the Motive bleeder reservoir. It's a great value, and I anticipate it being able to get the job done for years to come thanks to a solid design and quality materials at the price point.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By
Andrew Jones
Date: November 07, 2022
Nice Machine work, Close, Tight Tolerances.... Perfect, firm fit on an 05 Camry.... I always appreciate the that extra effort put into fit and finish, right down to that blue anodized aluminum!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]