5 out of 5
NewMar SPM-200 Site Power Monitor with Shunt, Price/1 EACH
* Click "Add to Shopping List" to save the item for later purchase. You can receive a notice email when it is back in stock.
Product Description
Price is for 1 EACH.
Manufacturer Part Number: SPM-200
NEWMAR Site Power Monitor. 9 Inputs DC voltage(3 Ports), AC voltage(2 Ports), CD Current(1 Port), Dry Contact Switch sensors(3 Ports). Includes Shunt.
Technical Specs
NEWMAR Site Power Monitor. 9 Inputs DC voltage(3 Ports), AC voltage(2 Ports), CD Current(1 Port), Dry Contact Switch sensors(3 Ports). Includes Shunt.
Technical Specs
| AC Input Voltage Range | 90-264 V |
| Item Length | 5 in |
| Item Height | 4 in |
| Total Inputs | 9 |
| AC Voltage Inputs | 2 ((1) 120/240 (90-264) Utility Power (L-N or L-L) and (1) 120/240 Inverter Output (Floating)) |
| Qty/ Uom | 1 Each |
| Item Width | 2 in |
| DC Current Inputs | 1 Port |
| Dry Contact Sensors | 3 Ports |
| Communication Interface | RJ-45 (Ethernet Port) and Compression Screw Terminal Block (14-26 AWG wire) |
| DC Input Voltage Range | 12-24 V |
| Comm. Protocols Supported | TCP/IP or SNMP |
| Test Equipment Connector Type | 1.25 mm Universal |
| Manufacturer | NewMar |
| Temperature Sensor | -40 to +60 Deg C (-40 to +140 Deg F) |
| DC Voltage Inputs | 3 ((2) 0-40 and (1) 36-60) |
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Return Policy
Following items are non-returnable:
Installed equipment and software.
Items listed as non-cancellable/non-returnable.
Value-added/tuned product.
Cut-to-length cable.
Installed equipment and software.
Items listed as non-cancellable/non-returnable.
Value-added/tuned product.
Cut-to-length cable.
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category
Customer Reviews
By John
Date: October 09, 2022
Perfect fit for my 96 Coleman Powerhouse 6250
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By A Customer
Date: September 24, 2022
A great and cost-effective solution to monitor power consumption for my 100A 120/240V 1-PH man cave electric panel. These power meters (one for each phase) display amperage, voltage, watts, frequency and records kWH, which is resettable. I flush mounted these accurate, easy to use, easy to read power meters in the lid of a 5”x8”x3” ABS project box.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By David Kirk
Date: August 25, 2022
I bought this pair to be able to track how much power my woodshop is consuming on a monthly basis. I used one for each leg of the 240 volt split phase panel. I had an enclosure and just cut holes for the display units. I extended the wires of the CT's with a similar gage wire with barrel crimps; and clipped the CT's over the incoming power cables. Only problem I had was I installed them upside down the first time because of the label orientation, and had to unsnap the clips and reverse everything. I used awg 12 for the voltage leads and tied it into a 240 volt ckt. (I know it should never get close to that ampacity, but if there was a short ckt, the breaker should trip without blowing the wires).Anyway, they work great. I am able to track my power consumption. It even reads power factor if you have induction motor and want to know if power factor correction is needed. Only complaint is when it goes over 10 KWH, it adds a leading zero. This makes it look like fractional KWH and I was confused at first until I realized there was no decimal point, just a leading 0.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Carla Kirk
Date: August 25, 2022
I bought this pair to be able to track how much power my woodshop is consuming on a monthly basis. I used one for each leg of the 240 volt split phase panel. I had an enclosure and just cut holes for the display units. I extended the wires of the CT's with a similar gage wire with barrel crimps; and clipped the CT's over the incoming power cables. Only problem I had was I installed them upside down the first time because of the label orientation, and had to unsnap the clips and reverse everything. I used awg 12 for the voltage leads and tied it into a 240 volt ckt. (I know it should never get close to that ampacity, but if there was a short ckt, the breaker should trip without blowing the wires).Anyway, they work great. I am able to track my power consumption. It even reads power factor if you have induction motor and want to know if power factor correction is needed. Only complaint is when it goes over 10 KWH, it adds a leading zero. This makes it look like fractional KWH and I was confused at first until I realized there was no decimal point, just a leading 0.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Gino A.
Date: July 21, 2022
These meters are installed easily, look and work great. I installed both meter digital displays in a 4x4-inch Cantex PVC junction box. Mounted the box just below the outside of my electrical panel and ran the wires through a knockout on the bottom of the panel and in a hole I drilled in the back of the junction box. Now I can accurately monitor the usage of this electrical sub-panel.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Danny
Date: July 19, 2022
I said it works well and will probably buy another one or two for garage panel, generator panel even some major loads like refrigerator etc
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]