0 reviews
Be the first to review this item!
Seal N Lock UWL5 Ultra-Wet-Look 5 gallon pail
Brand Seal N Lock
Shop more from JRA
* Click "Add to Shopping List" to save the item for later purchase. You can receive a notice email when it is back in stock.
Product Description
Manufacturer Part Number: UWL5
DESCRIPTION: Nano Technology, high solids, low VOC water based urethane modified acrylic for a wet look enhancement. Penetrates the pavers and provides a protective barrier with excellent joint stabilization. Ultra-Wet-Look is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with higher absorption rate will require additional application(s) of sealer.
ADVANTAGES:
ESTIMATING GUIDE: Typically, the application rate will vary from 150 to 175 sq. ft. per gallon; however, this rate will vary depending on the texture and absorption rate of the pavers and the width of the paver joints.
DIRECTIONS FOR USE: We recommend wearing protective goggles and latex gloves. For best results, apply Ultra-Wet-Look at temperatures between 50° F and 90° F. In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature is below 50°F. If temperature is going to drop below freezing (32° F) make sure sealer has time to cure. A test for compatibility, penetration, and adhesion is recommended. Do not seal if rain is in the near forecast.
NOTES:
Pavers with high absorption will require additional coats of sealer to provide protective barrier & desired enhancement
Ultra-Wet-Look is not intended for submerged surfaces
Too much sealer may induce a slippery condition
Do not seal if rain is in the near forecast
PROCEDURE:
1. Pressure Washing: Pressure wash the area to be sealed, ensuring that surfaces are clean and free of oil, efflorescence, laitance or contaminants prior to beginning the sealing process. Remove at least 1 to 2 inches of the old joint sand so new coarse sand can be replaced between the paver joints.
2. Rinsing: Rinse the pavers with water. If any acids/cleaners were used during the cleaning phase, make sure that the acids and cleaners are thoroughly rinsed before sealing.
3. Sanding: We recommend wet sanding with coarse fractured sand (C140) for joint sanding. Broadcast joint sand over the pavers. Rinse the sand into the paver joints to 1/8" below the chamfer edge of the pavers. See the video in our Educational Library www.sealnlock.com for more details. Also, you may sweep the sand into the paver joints, but must wait for the paver to dry. Use a leaf blower to blow off any residual sand left on the surface of the pavers.
4. Sealing: Ultra-Wet-Look may be applied even though the pavers are damp, but cannot be applied to pavers in standing water, as the sealer will not cure and stabilize the joint sand.
MIXING: Ultra-Wet-Look may be diluted to 1 part water and 1 part sealer for the first coat (Flood Coat for joint stabilization) and the topcoat may be applied 1 part water to 1 part sealer, or straight without dilution for an Ultra-Wet-Look appearance. Mix and stir prior to use. We recommend multiple coats for extremely absorbent pavers. Using our battery operated pail pump system or pump sprayer, uniformly apply a flood coat of sealer for joint stabilization. Hold sprayer tip 10" - 12" from the paver surface (avoid overspray on adjacent surfaces, rinse any overspray with water). Ultra-Wet-Look appears white when applied but dries crystal clear. Make sure to apply sealer consistently to prevent blotching. (Back rolling is recommended for consistency) Pavers with polymeric sand, we recommend two even consistent coats of sealer diluted 1 part water to 1 part sealer without flooding the paver joints. Use a leaf blower to blow out any excess sealer that puddles in the paver joints or low lying areas with textured pavers and or natural stone.
5. Resealing Existing Sealed Pavers: Ultra-Wet-Look may be applied over existing sealed pavers, as long as there is no delaminating (peeling) of existing sealer and is worn evenly. If there are any shiny areas or areas that are white from solvent base sealer we recommend stripping the existing sealer before applying our Ultra-Wet-Look. Call your distributor for technical support in regard to the stripping process.
DRYING TIME: Ultra-Wet-Look will normally dry in sunny areas within approximately a few hours. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 4 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns. Always check for tackiness before foot and especially vehicle traffic.
MAINTENANCE: Periodic washing of the pavers with a mild detergent to keep the area clean is recommended. DO NOT USE ACIDS. Gasoline, hydraulic fluids, and motor oil spills should be removed from the surface of the pavers. We recommend that surfaces previously sealed should be pressure washed, re-sanded and resealed every 2 to 3 years depending on environmental exposure and traffic.
CLEANUP: Immediately flush pump system after use with water.
Quick Overview
- User-friendly and environmentally safe
- May be applied to a damp substrate (eliminating downtime)
- Provides protective barrier
- One day process (no downtime)
- Immediately flush pump system after use with water.
Ultra-Wet-Look 5 gallon pail
DESCRIPTION: Nano Technology, high solids, low VOC water based urethane modified acrylic for a wet look enhancement. Penetrates the pavers and provides a protective barrier with excellent joint stabilization. Ultra-Wet-Look is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with higher absorption rate will require additional application(s) of sealer.
ADVANTAGES:
- One day process (no downtime)
- Provides protective barrier
- May be applied to a damp substrate (eliminating downtime)
- User-friendly and environmentally safe
- 35% solids
- Minimum toxic odor
- Will not harm vegetation and inhibits weed growth and ant mines
- Algae and mold inhibitor
- Excellent joint stabilization (for paver joints up to 1/4" width), no need for polymeric sand
- VOV <119 G/L
- UV Protection
ESTIMATING GUIDE: Typically, the application rate will vary from 150 to 175 sq. ft. per gallon; however, this rate will vary depending on the texture and absorption rate of the pavers and the width of the paver joints.
DIRECTIONS FOR USE: We recommend wearing protective goggles and latex gloves. For best results, apply Ultra-Wet-Look at temperatures between 50° F and 90° F. In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature is below 50°F. If temperature is going to drop below freezing (32° F) make sure sealer has time to cure. A test for compatibility, penetration, and adhesion is recommended. Do not seal if rain is in the near forecast.
NOTES:
Pavers with high absorption will require additional coats of sealer to provide protective barrier & desired enhancement
Ultra-Wet-Look is not intended for submerged surfaces
Too much sealer may induce a slippery condition
Do not seal if rain is in the near forecast
PROCEDURE:
1. Pressure Washing: Pressure wash the area to be sealed, ensuring that surfaces are clean and free of oil, efflorescence, laitance or contaminants prior to beginning the sealing process. Remove at least 1 to 2 inches of the old joint sand so new coarse sand can be replaced between the paver joints.
2. Rinsing: Rinse the pavers with water. If any acids/cleaners were used during the cleaning phase, make sure that the acids and cleaners are thoroughly rinsed before sealing.
3. Sanding: We recommend wet sanding with coarse fractured sand (C140) for joint sanding. Broadcast joint sand over the pavers. Rinse the sand into the paver joints to 1/8" below the chamfer edge of the pavers. See the video in our Educational Library www.sealnlock.com for more details. Also, you may sweep the sand into the paver joints, but must wait for the paver to dry. Use a leaf blower to blow off any residual sand left on the surface of the pavers.
4. Sealing: Ultra-Wet-Look may be applied even though the pavers are damp, but cannot be applied to pavers in standing water, as the sealer will not cure and stabilize the joint sand.
MIXING: Ultra-Wet-Look may be diluted to 1 part water and 1 part sealer for the first coat (Flood Coat for joint stabilization) and the topcoat may be applied 1 part water to 1 part sealer, or straight without dilution for an Ultra-Wet-Look appearance. Mix and stir prior to use. We recommend multiple coats for extremely absorbent pavers. Using our battery operated pail pump system or pump sprayer, uniformly apply a flood coat of sealer for joint stabilization. Hold sprayer tip 10" - 12" from the paver surface (avoid overspray on adjacent surfaces, rinse any overspray with water). Ultra-Wet-Look appears white when applied but dries crystal clear. Make sure to apply sealer consistently to prevent blotching. (Back rolling is recommended for consistency) Pavers with polymeric sand, we recommend two even consistent coats of sealer diluted 1 part water to 1 part sealer without flooding the paver joints. Use a leaf blower to blow out any excess sealer that puddles in the paver joints or low lying areas with textured pavers and or natural stone.
5. Resealing Existing Sealed Pavers: Ultra-Wet-Look may be applied over existing sealed pavers, as long as there is no delaminating (peeling) of existing sealer and is worn evenly. If there are any shiny areas or areas that are white from solvent base sealer we recommend stripping the existing sealer before applying our Ultra-Wet-Look. Call your distributor for technical support in regard to the stripping process.
DRYING TIME: Ultra-Wet-Look will normally dry in sunny areas within approximately a few hours. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 4 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns. Always check for tackiness before foot and especially vehicle traffic.
MAINTENANCE: Periodic washing of the pavers with a mild detergent to keep the area clean is recommended. DO NOT USE ACIDS. Gasoline, hydraulic fluids, and motor oil spills should be removed from the surface of the pavers. We recommend that surfaces previously sealed should be pressure washed, re-sanded and resealed every 2 to 3 years depending on environmental exposure and traffic.
CLEANUP: Immediately flush pump system after use with water.
| SDS Sheet | ||
NOTE: Price is only for Model #: 320-707
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category