skip to footer block
DLA D. Lawless Hardware Chrome Glass Door Hinge Pair S HT86SK P12189317DLA-S-HT86SK https://cdnimages.opentip.com/full/DLA/DLA-S-HT86SK.jpg D. Lawless Hardware Chrome Glass Door Hinge Pair S HT86SK Product Overview SPECIAL ORDER ONLY - 300 PAIRS MINIMUM Contact us for quote. Pair Chrome Plated Glass Door Hinges, Set Steel Screw, fits 3/16\" to 1/4\" glass. Comes with protective inserts and bushings. For inset application.See Tech-Info for installation procedures. D. Lawless HardwareInstallation:1. Locate the centers for the bushings. This hole should be located or drilled 15/32\" (12mm) away from the inside of the cabinet face. Hole diameter to drill is 9mm. Hole depth 10mm.2. To drill these pivot bushing holes, it is best to use a metric brad point drill set. If you do not have a metric set, use a standard fractional set and drill a 11/32\" diameter hole.3.If the cabinet is not already assembled, do so now. Insert bushings, then hinges into bushings. Measure the vertical distance between the insides of the hinges where glass will fit. Deduct 2mm from this measurement to allow for clearance. Cut glass panel according to this calculation.4. Install pressure plates. Place lower hinge into bushings. Slide bottom corner of glass door into hinge. Hold door swung outward. It should swing out to about 60 degrees. Now place upper hinge into bushing and slide top of door into hinge. Adjust door glass panel to what appears to be a good lateral position, and tighten one screw in each hinge.5. Make final adjustments for fit and alignment by loosening set screws and slipping glass into final position. Then, tighten both set screws. 12189317 0.5000lbs 0.00 0.00 0.00
D. Lawless Hardware
4.5500 2025-04-26 100 In Stock

D. Lawless Hardware Chrome Glass Door Hinge Pair S-HT86SK

Shop more from DLA

SKU: DLA-S-HT86SK
Price: $4.55
Minimum Order: $66.00 minimum order amount required, mix more items >
Quantity:
100 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Product Description

Product Overview

SPECIAL ORDER ONLY - 300 PAIRS MINIMUM Contact us for quote. Pair Chrome Plated Glass Door Hinges, Set Steel Screw, fits 3/16" to 1/4" glass. Comes with protective inserts and bushings. For inset application.

See Tech-Info for installation procedures. D. Lawless Hardware

Installation:
1. Locate the centers for the bushings. This hole should be located or drilled 15/32" (12mm) away from the inside of the cabinet face. Hole diameter to drill is 9mm. Hole depth 10mm.
2. To drill these pivot bushing holes, it is best to use a metric brad point drill set. If you do not have a metric set, use a standard fractional set and drill a 11/32" diameter hole.
3.If the cabinet is not already assembled, do so now. Insert bushings, then hinges into bushings. Measure the vertical distance between the insides of the hinges where glass will fit. Deduct 2mm from this measurement to allow for clearance. Cut glass panel according to this calculation.
4. Install pressure plates. Place lower hinge into bushings. Slide bottom corner of glass door into hinge. Hold door swung outward. It should swing out to about 60 degrees. Now place upper hinge into bushing and slide top of door into hinge. Adjust door glass panel to what appears to be a good lateral position, and tighten one screw in each hinge.
5. Make final adjustments for fit and alignment by loosening set screws and slipping glass into final position. Then, tighten both set screws.

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item


Customer Reviews
0 reviews
Be the first to review this item!