5 out of 5
Audtek Infrared Repeater System Kit Dual Band
* Click "Add to Shopping List" to save the item for later purchase. You can receive a notice email when it is back in stock.
Pricing Note
Product Description
Manufacturer Part Number: DBIRX
This IR repeater kit from Audtek Electronics has everything needed to get started with a distributed infrared system. Get that A/V equipment out of sight without sacrificing control!
Key Features:
Audtek Infrared Repeater System Kit Dual Band
With a Audtek Electronics IR Repeater system, you can locate your A/V components out of sight in a closet or cabinet and still use your remote control.
The central module features industry-standard jacks for power, target, and emitters, so no tools are needed for installation. Screw tabs on the sides of the control module allow it to be permanently attached to just about any surface. The system includes two double-emitters with two meter cords, to control up to four devices. The target has a one meter cord so it can be located away from the control module. There are two LEDs on the control module; the red LED shows the system has power and the green LED flashes to show signal transmission. A 5V DC power supply is included.
This IR repeater kit from Audtek Electronics has everything needed to get started with a distributed infrared system. Get that A/V equipment out of sight without sacrificing control!
Key Features:
- Transmits both 38 kHz and 56 kHz IR bands
- Control AV components located behind closed doors
- Easy setup, no tools needed
- Includes 2 dual-output emitters
- Emitters snap into a unique saddle for easy removal
Audtek Infrared Repeater System Kit Dual Band
With a Audtek Electronics IR Repeater system, you can locate your A/V components out of sight in a closet or cabinet and still use your remote control.
The central module features industry-standard jacks for power, target, and emitters, so no tools are needed for installation. Screw tabs on the sides of the control module allow it to be permanently attached to just about any surface. The system includes two double-emitters with two meter cords, to control up to four devices. The target has a one meter cord so it can be located away from the control module. There are two LEDs on the control module; the red LED shows the system has power and the green LED flashes to show signal transmission. A 5V DC power supply is included.
Product Details | |
|---|---|
| Brand | Audtek Electronics |
| Model | DBIRX |
| Part Number | 180-701 |
| UPC | 844632001437 |
| Unit of Measure | Each |
| Weight | 0.75 |
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category
Customer Reviews
By Tom
Date: December 04, 2016
I'm using this to extend the remote control for a magnavox dvr from one room to another. I run the analog video feed from it to two room, and use the IR kit to receive the remote from one room and transmit to the other via cat5 cable. To do that, I just made an adapter for the IR emitter, to make that cable about 50 feet longer. Works perfectly. The other reviewer is correct, it's tough to spot where the IR sensor is for some equipment. This works, at least for the magnavox, when the emitter is up to 1234; or more away from the unit. Depending on your installation, that might make it easier to line up. The other suggestion I have is that if you want to make a room to room extension, to extend on the transmit side, as it's only 2 wires and shouldn't pick up noise. The receive units are 3 wire, and might pickup noise.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
Items 1 - 1 of 1 reviews
1