skip to footer block
PEX Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118 P10456103PEX-310-4002 https://cdnimages.opentip.com/full/PEX/PEX-310-4002.jpg Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118 Manufacturer Part Number: LP210PAThe Lepai LP210PA is the ideal Class D plate amplifier for powering smaller 2.1 speaker systems. This compact plate amplifier can provide 30 watts x 2 to the full-range outputs and 60 watt to the mono subwoofer channel for powerful output capability. The adjustable crossover frequency, sub volume, and main speaker volume makes it easy to create a smooth transition from a subwoofer to satellite speakers.Key Features: Compact size (4.5\" x 5\" x 1\") for installation into the smallest subwoofer enclosures Satellite outout includes 6 dB per octave high pass at 100 Hz Perfect for use in office, bedroom, or even portable speaker systems Defeatable full range output for use as just a subwoofer amplifier The full-range speaker output uses high quality binding posts for easy connection Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118Lepai\'s LP210PA compact 2.1 plate amplifier makes it easy to create your own powered subwoofer/satellite speaker systems. At only 4.5\" wide and 5\" tall, you can install this amplifier in even the smallest subwoofer designs; however with 60 watts to the subwoofer and 30 watts to each satellite you can expect powerful output capability. This is the perfect plate amplifier for use in office, bedroom, or even portable subwoofer/satellite speaker systems.The straightforward features make the LP210PA extremely easy to connect and setup. Input is handled through stereo RCA connectors. For the power outputs, there is a Phoenix connector on the back of the amplifier to connect directly to your subwoofer driver, along with binding posts on the front of the plate for simple connection to a pair of separate satellite speakers. The adjustable subwoofer volume, crossover frequency, and main speaker volume makes it easy to create a smooth transition between the subwoofer and satellite speakers. In addition, this amplifier includes a unique channel selection switch, which allow you to turn off the satellite speakers and run just the subwoofer by itself allowing you to run separate powered satellites from the stereo RCA pass through outputs.Note: Power supply not included.Specifications: Output power: 2 x 30 watts + 1 x 60 watts RMS Minimum impedance: 4 ohms Amplifier chip: 2 x TPA3118 Frequency response: 20 to 20,000 Hz, Subwoofer output: 20 to 150 Hz Subwoofer crossover: adjustable 30 - 150 Hz 12 dB/octave Satellite Crossover: fixed 100 Hz 6 dB/octave Input sensitivity: 245 mV Input: RCA (with pass through outputs) Outputs: Phoenix connector (subwoofer), binding posts (left and right outputs) Power requirement: 15 - 22 VDC (2.5mm x 5.5mm plug) Plate amplifier dimensions: 4.5\" W x 5\" H x 1\" D (hole size: 3.75\" W x 4.125\" H).Product Details BrandLepai ModelLP210PA Part Number310-4002 UPC848864051369 Unit of MeasureEach Weight0.55 10456103 848864051369 0.5500lbs 0.00 0.00 0.00
Lepai
62.98 2025-04-23 287 In Stock
customer review - by , November 11, 2022
5/ 5stars
Lepai is a fine brand. Have 3 products from them some are 10 years old. The 20amp tripath amp is an overachiever. It performs,and stays cool. Sound quality is surprisingly awesome. This plate amp is powering an 8in. Jbl power series gt. Woofer 100w. In a 12x12x12 box. Sealed. It rocks. Using it on spare t.v for cheap surround sound system. The other channel is full range driving two old Kenwood surround speakers 40w each. Also a quality plate amp at a rediculously low price. Will buy more and make more subs as presents for family. Volume is awesome in a medium to small room. 60w and 30x30w is,nt going to wake the neighbors. Its a cheap alternative to high end plates. Use a better power supply with 19v 4.5a like fosi . Works great. Buy seperate and it,ll pay for itself in the long run. Less nonsence. No buzzing. Clean sound.
customer review - by , October 10, 2022
5/ 5stars
Using this as the amp/controller for a 2.1 desktop system and am very happy with it. Here's what you need to know and should be paying attention to:1. The amp takes a DC power input, standard 5.5mm x 2.1mm barrel connector, 15-22 volts. The more voltage you feed it, the less hard it has to work to meet rated specs. If you use a 15-volt, 3-amp wall wart power supply, it will work but you won't be impressed. I am using an adjustable DC power supply. I am feeding it 21 volts with 20 amps of available current. It will never draw more than 5 amps at 21 volts and that's exactly the point. More available power up to the 22v maximum is better. I'd consider 19 volts 4 amps the minimum voltage to feed this amp and expect good results.2. The amp is rated at 60w x 1 for the sub and 30w x 2 for the L/R 4 ohms. Emphasis on 4 ohms. Cut those ratings in half for an 8 ohm load. 15 watts for the satellites is plenty, but 30 watts for a sub is not great. I'm using a 4-ohm driver in my subwoofer, so am getting the full 60 watts for the sub. For a desktop or small living room setup, this is plenty of wattage. For reference, I built a Voxel subwoofer and the Overnight Sensations desktop speakers. The setup is way louder than I need it to be for my office/gaming system usage.3. The amp has a fixed 100Hz/6db oct highpass on the L/R speaker outputs. You will not get much bass out of your satellites, but that's the point of this amp. It's meant for smaller, L/R speakers and a sub. If you need a 2-channel full range amp, buy one of those, not this 2.1 channel amp.4. The amp has an adjustable 6db/oct lowpass on the sub output. This makes it very easy to blend the sub with your satellites (your L/R speakers) and it works well.5. The amp has individual level controls for both the sub and the satellites. THIS is the feature missing on many 2.1 amps. This ability to balance the levels of the sub and satellites independent from each other is what makes this 2.1 amp fantastic.6. Low noise floor, small cutout required, fits basically anywhere.I've only been using it for a couple of weeks, so can't speak to the longevity. But, so far, so good. HIGHLY recommended.
customer review - by , November 11, 2021
5/ 5stars
I'm using this to power a Dayton Audio DCS165-4 6-1/2 subwoofer in a 0.5 ft^3 box and a set of Dayton Audio B452 bookshelf speakers. Power supply is 19V 6.32A so it's getting 120 watts. It's more than enough for an office setup.
customer review - by , July 7, 2021
5/ 5stars
Great small plate amp. Offers plenty of power for a small sub and the versatility to power two satellite speakers as will. The 2.1/ .1 channel option is a great feature for this little amp. All important connections are well labeled on the board so wiring and upgrading should be easy. The only thing missing is a signal sensor for power on/off. You have to manually switch it on/off. Still a great little amp.
customer review - by , November 11, 2020
4/ 5stars
when the sub amp on my Sim Racing Rig failed I looked around. Most plate amps where over $100 dollars. This little amp was 1/3 the price. It is also very well made. Once installed in my sub box. The power is clean and it has a pass through for both the right and left channels. Best amp I've bought in years
customer review - by , July 7, 2020
5/ 5stars
  »  
  »  
  »  
  »  
  »  
  »  

Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118

stars Rating 5 | 6 reviews
Brand Lepai
Shop more from PEX
UPC: 848864051369
SKU: PEX-310-4002
Price:
$62.98Free shipping on orders over $65 on select PEX- items. Details
Buy in bulk & save 11% ($56.26 each)
Quantity:
287 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk
*  Price: $62.98 ea X 1 qty = $62.98
Quantity Price Save
1+ $62.98 0%
4+ $56.26 11%
* This item is excluded from use of other offer, discount or coupon.

Pricing Note

Free Shipping Promotion: Buy more items from the same series, product code beginning with PEX-, and you can get free shipping for an order of over  $65.00  consisting of only PEX- series products.

Product Description

Manufacturer Part Number: LP210PA

The Lepai LP210PA is the ideal Class D plate amplifier for powering smaller 2.1 speaker systems. This compact plate amplifier can provide 30 watts x 2 to the full-range outputs and 60 watt to the mono subwoofer channel for powerful output capability. The adjustable crossover frequency, sub volume, and main speaker volume makes it easy to create a smooth transition from a subwoofer to satellite speakers.

Key Features:
  • Compact size (4.5" x 5" x 1") for installation into the smallest subwoofer enclosures
  • Satellite outout includes 6 dB per octave high pass at 100 Hz
  • Perfect for use in office, bedroom, or even portable speaker systems
  • Defeatable full range output for use as just a subwoofer amplifier
  • The full-range speaker output uses high quality binding posts for easy connection


Lepai LP210PA 2x30W + 60W 2.1 Channel Mini Plate Amplifier TPA3118

Lepai's LP210PA compact 2.1 plate amplifier makes it easy to create your own powered subwoofer/satellite speaker systems. At only 4.5" wide and 5" tall, you can install this amplifier in even the smallest subwoofer designs; however with 60 watts to the subwoofer and 30 watts to each satellite you can expect powerful output capability. This is the perfect plate amplifier for use in office, bedroom, or even portable subwoofer/satellite speaker systems.

The straightforward features make the LP210PA extremely easy to connect and setup. Input is handled through stereo RCA connectors. For the power outputs, there is a Phoenix connector on the back of the amplifier to connect directly to your subwoofer driver, along with binding posts on the front of the plate for simple connection to a pair of separate satellite speakers. The adjustable subwoofer volume, crossover frequency, and main speaker volume makes it easy to create a smooth transition between the subwoofer and satellite speakers. In addition, this amplifier includes a unique channel selection switch, which allow you to turn off the satellite speakers and run just the subwoofer by itself allowing you to run separate powered satellites from the stereo RCA pass through outputs.

Note: Power supply not included.

Specifications: Output power: 2 x 30 watts + 1 x 60 watts RMS Minimum impedance: 4 ohms Amplifier chip: 2 x TPA3118 Frequency response: 20 to 20,000 Hz, Subwoofer output: 20 to 150 Hz Subwoofer crossover: adjustable 30 - 150 Hz 12 dB/octave Satellite Crossover: fixed 100 Hz 6 dB/octave Input sensitivity: 245 mV Input: RCA (with pass through outputs) Outputs: Phoenix connector (subwoofer), binding posts (left and right outputs) Power requirement: 15 - 22 VDC (2.5mm x 5.5mm plug) Plate amplifier dimensions: 4.5" W x 5" H x 1" D (hole size: 3.75" W x 4.125" H).

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item
Request More Information

Look Similar Items By Category

Electronics > Car & Vehicle Electronics > Car Electronics > Car Audio > Amplifiers
Automotive > Car Electronics & Accessories > Car Electronics > Car Audio > Amplifiers
Customer Reviews
5 out of 5
see all 6 reviews
5 stars
5
4 stars
1
3 stars
0
2 stars
0
1 stars
0
Write a Review
By James Wheat
Date: November 09, 2020
when the sub amp on my Sim Racing Rig failed I looked around. Most plate amps where over $100 dollars. This little amp was 1/3 the price. It is also very well made. Once installed in my sub box. The power is clean and it has a pass through for both the right and left channels. Best amp I've bought in years
Rating: 4 stars [4 of 5 Stars!]
Items 1 - 1 of 1 reviews
 1