JRA J.Racenstein HSLR10 Rotary Brush 39 inch 100cm Water Powered P13172408JRA-159-136 https://cdnimages.opentip.com/full/JRA/JRA-159-136.jpg J.Racenstein HSLR10 Rotary Brush 39 inch 100cm Water Powered Manufacturer Part Number: HSLR10Quick OverviewDesigned to clean solar panels, vinyl, and aluminum sidingIt is a mobile, hand-operated unit designed to be controlled manuallyHydrokinetic brushes save considerable time compared to traditional brushesRequirements: 580 psi at brush head max and 2.3 gallons per minute consumptionBrush 39in Water Powered for Cleaning Large SurfacesThe rotating roller brush was designed and built to clean solar panels, vinyl and aluminum siding.It is a mobile, hand-operated unit designed to be positioned and operated manually on the surface to be cleaned.Rotary hydrokinetically brushes offer considerable time savings in the cleaning operation performed on solar panels and building surfaces when compared to traditional fixed brushes.Requirements:- 600 to 700PSI (40 to 50 BAR) pressure at brush head max- 2.3 to 3 Gallons per minute (9 to 11LPM) consumptionMax. Water Temperature: 104° F (40° C)For Pressure washing sizing the brush is the same usage as a #7 tipPressure washer:Recommended Pressure Washer: 3 gallons per minute, 2500psiWeight: 12.5lbs32inch Rotating Brush Water Powered for Solar PanelsRegulator and GaugeUse a Pressure Gauge to undestand the pressure at the brushInstall the Gauge on the water connector on the brushTest Run your your pressure washer and supply water to the brush from your running pressure washer the PSI should be between 290 psi and 725 psi.One you have your system setup at the correct pressure ytou can remove and store the gauge for future testingAlway test again after a pressure washer has been worked on or should a different pressre washer is put in place to power the brushNOTE:If your pressure Washer is running the brush at more that 725PSI then immediatly stop the water flow.You can try a smaller pressure washer or install and adjust a Pressure Regulator to set the pressure to the suggested 600 to 650 psi to run the brush. (Max 725psi)How to check your Flow from your Pressure WasherPlace the brush over a 5 Gallon bucket and time how long it takes to Fill the 5 Gallon Bucket it should be filled in between1min 50 seconds (2.7 gpm) and2 min 20 seconds (2.14 gpm) this is measured at a max of 725psi at the brush, anything longer than 2 minutes 30 seconds is not enough flow.Regulator and Guage not includedTesting and Setting Water Pressure If your pressure washer is to big you will need to usea Pressure Regulator to control the Pressure - Target 600 to 650 PSI.Here the gauge is installed Attached to the Pressure washer and run the brush, ig you are between 550 and 650psi you are good to go.Attach a Pressure Regulator and Test, Set PSIIf the pressure is more than 725 PSI then install and adjust a pressure regulator to the target of 600 to 650psi. (Max 725)Gauge can be removed for day to day useOnce you know your settings are correct you may remove th egauge for day to day cleaningKeep the gauge handy should the pressure washer used be swapped out so you can test again159-135_Rotary-Brush-24in[1].pdfParts-List-Rotary-Brush-32in-39in-159-1361.pdf 13172408 5.77lbs 0.00 0.00 0.00
J.Racenstein
2916.2400 2023-08-08 Only 1 left In Stock
Share to:

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Brand J.Racenstein
See other products from JRA

SKU: JRA-159-136
Price: $2,916.24
Quantity:
Only 1 left In Stock
*  Shipping Note: Usually ships within 9 to 10 days.
Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Optional related products

Product Description

Manufacturer Part Number: HSLR10

Quick Overview

  • Designed to clean solar panels, vinyl, and aluminum siding
  • It is a mobile, hand-operated unit designed to be controlled manually
  • Hydrokinetic brushes save considerable time compared to traditional brushes
  • Requirements: 580 psi at brush head max and 2.3 gallons per minute consumption

Brush 39in Water Powered for Cleaning Large Surfaces



The rotating roller brush was designed and built to clean solar panels, vinyl and aluminum siding.

It is a mobile, hand-operated unit designed to be positioned and operated manually on the surface to be cleaned.

Rotary hydrokinetically brushes offer considerable time savings in the cleaning operation performed on solar panels and building surfaces when compared to traditional fixed brushes.

Requirements:

- 600 to 700PSI (40 to 50 BAR) pressure at brush head max

- 2.3 to 3 Gallons per minute (9 to 11LPM) consumption

Max. Water Temperature: 104° F (40° C)

For Pressure washing sizing the brush is the same usage as a #7 tip

Pressure washer:

Recommended Pressure Washer: 3 gallons per minute, 2500psi

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Weight: 12.5lbs

32inch Rotating Brush Water Powered for Solar Panels

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water PoweredJ.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Regulator and Gauge


Use a Pressure Gauge to undestand the pressure at the brush

Install the Gauge on the water connector on the brush

Test Run your your pressure washer and supply water to the brush from your running pressure washer the PSI should be between 290 psi and 725 psi.

One you have your system setup at the correct pressure ytou can remove and store the gauge for future testing

Alway test again after a pressure washer has been worked on or should a different pressre washer is put in place to power the brush

NOTE:

If your pressure Washer is running the brush at more that 725PSI then immediatly stop the water flow.

You can try a smaller pressure washer or install and adjust a Pressure Regulator to set the pressure to the suggested 600 to 650 psi to run the brush. (Max 725psi)

How to check your Flow from your Pressure Washer

Place the brush over a 5 Gallon bucket and time how long it takes to Fill the 5 Gallon Bucket it should be filled in between
  • 1min 50 seconds (2.7 gpm) and
  • 2 min 20 seconds (2.14 gpm)
this is measured at a max of 725psi at the brush, anything longer than 2 minutes 30 seconds is not enough flow.

Regulator and Guage not included

Testing and Setting Water Pressure



If your pressure washer is to big you will need to usea Pressure Regulator to control the Pressure - Target 600 to 650 PSI.

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Here the gauge is installed


Attached to the Pressure washer and run the brush, ig you are between 550 and 650psi you are good to go.

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Attach a Pressure Regulator and Test, Set PSI


If the pressure is more than 725 PSI then install and adjust a pressure regulator to the target of 600 to 650psi. (Max 725)

J.Racenstein HSLR10 Rotary Brush 39 inch (100cm) Water Powered

Gauge can be removed for day to day use


Once you know your settings are correct you may remove th egauge for day to day cleaning

Keep the gauge handy should the pressure washer used be swapped out so you can test again


NOTE: Images are just for your reference, price is only for Model #: 159-136


This item is oversize. we may contact you when we process the order.

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.

You may also like
Need more information?
Our staff are available to answer any questions you may have about this item


Look Similar Items By Category


Customer Reviews
0 reviews
Be the first to review this item!