skip to footer block
HDL FastCap Magnetic Spacers for Saws P6646453HDL-FCMAG-SHIMS-S https://cdnimages.opentip.com/full/HDL/HDL-FCMAG-SHIMS-S.jpg FastCap Magnetic Spacers for Saws FastCap Mag ShimsMag Shims are the easiest way to set your blade height and fence spacing on your table saw. Simply stick the magnetic shims together to get a perfect setup in seconds! Also great for setting depth on drill presses.8 - 1/8\" thick magnetic shims2 - 1/16\" metal shimsMagnetic ShimsProduct SKUColorUnitFCMAG SHIMS SRedEA 6646453 663807048615 0.4440lbs 0.00 0.00 0.00
FastCap
31.2700 2025-04-25 7 In Stock
customer review - by , March 3, 2018
5/ 5stars
I havent had these long but use them all the time nearly every time Im in the workshop Its surprising how handy they are Ive even used the corners to mark out corner curves They have strong magnets so they store easily on any metal surface The only warning is that they really will pinch your fingers You need to hold them back away when you are putting them back with the group Theyll fly back together without your finger in the middle No complaint about this because I like the strong magnets Just something to learn to use correctly I may get the mm ones sometime though I dont use metric that often Metric has somewhat smaller increments though the 18 ones make a taller stack overall I like having the two 116 ones especially
customer review - by , January 1, 2018
5/ 5stars
I’ve used this set of gauges far more than I thought I would They are very handy for many set up tasks on my saw and router For example I was able to easily position my router bit to the center of a board using the 116 gauge in conjunction with the one-eighth gauges Good quality The magnets really stick together well The plastic is super tough Worth the moneyAD2
customer review - by , December 12, 2017
5/ 5stars
Works well like the a lot
customer review - by , October 10, 2017
5/ 5stars
Really does make saw set-up blades distances) a breeze and accurate Normally I have to take two measurements fore and aft) on my table saw to adjust the fence Now I just set the gauge down and its done
customer review - by , July 7, 2017
3/ 5stars
It does what I want it to do
customer review - by , July 7, 2016
5/ 5stars
They work great for setting the depth of router cuts table saw depth offsetsand store nicely stuck to the side of my table saw for easy access
customer review - by , June 6, 2016
5/ 5stars
Easy to use accurate measurement tool I use it for setting my routers depth adjustment
  »  
  »  
  »  
  »  
  »  

FastCap Magnetic Spacers for Saws, Price/Each

stars Rating 5 | 7 reviews
Brand FastCap
Shop more from HDL
UPC: 663807048615
SKU: HDL-FCMAG-SHIMS-S
Price: $31.27
Quantity:
7 In Stock
*  Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Product Description

Price is for Each.

FastCap Mag Shims

Mag Shims are the easiest way to set your blade height and fence spacing on your table saw. Simply stick the magnetic shims together to get a perfect setup in seconds! Also great for setting depth on drill presses.

  • 8 - 1/8" thick magnetic shims
  • 2 - 1/16" metal shims


Magnetic Shims



FastCap Magnetic Spacers for Saws

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.

Return Policy

We do not accept returns if the product has been tried to be installed.
Need more information?
Our staff are available to answer any questions you may have about this item
Request More Information

Customer Reviews
5 out of 5
see all 7 reviews
5 stars
6
4 stars
0
3 stars
1
2 stars
0
1 stars
0
Write a Review
By K Medlar
Date: March 14, 2018
I havent had these long but use them all the time nearly every time Im in the workshop Its surprising how handy they are Ive even used the corners to mark out corner curves They have strong magnets so they store easily on any metal surface The only warning is that they really will pinch your fingers You need to hold them back away when you are putting them back with the group Theyll fly back together without your finger in the middle No complaint about this because I like the strong magnets Just something to learn to use correctly I may get the mm ones sometime though I dont use metric that often Metric has somewhat smaller increments though the 18 ones make a taller stack overall I like having the two 116 ones especially
Rating: 5 stars [5 of 5 Stars!]
By Alan Dale Daniel
Date: January 20, 2018
I’ve used this set of gauges far more than I thought I would They are very handy for many set up tasks on my saw and router For example I was able to easily position my router bit to the center of a board using the 116 gauge in conjunction with the one-eighth gauges Good quality The magnets really stick together well The plastic is super tough Worth the moneyAD2
Rating: 5 stars [5 of 5 Stars!]
By Neil K.
Date: December 28, 2017
Works well like the a lot
Rating: 5 stars [5 of 5 Stars!]
By Jakob C. Froisland
Date: October 05, 2017
Really does make saw set-up blades distances) a breeze and accurate Normally I have to take two measurements fore and aft) on my table saw to adjust the fence Now I just set the gauge down and its done
Rating: 5 stars [5 of 5 Stars!]
By anthony roppolo
Date: July 26, 2017
It does what I want it to do
Rating: 3 stars [3 of 5 Stars!]
By DB
Date: July 20, 2016
They work great for setting the depth of router cuts table saw depth offsetsand store nicely stuck to the side of my table saw for easy access
Rating: 5 stars [5 of 5 Stars!]
Items 1 - 6 of 7 reviews
 1  2  [Next]