5 out of 5
Dayton Audio DAEX25Q-4 Quad Feet 25mm Exciter 20W 4 Ohm
* Click "Add to Cart" to calculate shipping and delivery time.
Pricing Note
Product Description
Manufacturer Part Number: DAEX25Q-4
Dayton Audio's DAEX25Q-4 features four extended arms for turning larger surfaces into speakers, while providing more bass output . Spring-loaded speaker terminals facilitate quick electrical connection.
Key Features:
Dayton Audio DAEX25Q-4 Quad Feet 25mm Exciter 20W 4 Ohm
Dayton Audio's DAEX25Q-4 quad arm exciter is built with four arms that extend out from the main exciter body, which allows this exciter to transfer sound to a much larger surface for lower frequency response extension (more bass).
A neodymium magnet is employed to create maximum magnetic flux around the proprietary voice coil for increased sensitivity when compared to similar sized exciters. In turn, this reduces power requirements and makes it possible to use very small audio amplifiers, without sacrificing total output. The 1" voice coil allows for more input power, creating rich, dynamic sound.
To ensure maximum acoustic energy transfer between the transducer and the surface to which it is attached, 3M VHB (Very High Bond) adhesive is pre-applied to the main body, and the four arms ... just peel and stick! Two spring-loaded terminals are built onto the main body for quick electrical connection.
Note: An exciter's frequency response and sensitivity are completely dependent on the exciter's designated surface. Thinner, smaller materials will tend to be louder and create a mid/tweeter response. Thicker, larger materials (with multiple exciters) will be slightly quieter but result in a more full-range sound.
Specifications: Power handling: 20 watts RMS VCdia: 25 mm Nominal impedance: 4 ohms Re: 4.3 ohms Le: 0.25 mH Fs (uncoupled): 224 Hz Dimensions: 3.99" (101.44 mm) overall diameter x 0.97" (24.7 mm) total height Weight: 90.5 grams.
To learn more about Dayton Audio Exciters, and for help on which Exciter is right for you, check out .
Dayton Audio's DAEX25Q-4 features four extended arms for turning larger surfaces into speakers, while providing more bass output . Spring-loaded speaker terminals facilitate quick electrical connection.
Key Features:
- Unique, four arm design for exciting a large surface
- Pre-applied 3M™ VHB™ adhesive for quick, secure installation
- Rare-earth neodymium motor and a proprietary voice coil
- 4-ohm impedance for use with small, Class D amplifiers
- 20 watt RMS power handling for high output
Dayton Audio DAEX25Q-4 Quad Feet 25mm Exciter 20W 4 Ohm
Dayton Audio's DAEX25Q-4 quad arm exciter is built with four arms that extend out from the main exciter body, which allows this exciter to transfer sound to a much larger surface for lower frequency response extension (more bass).
A neodymium magnet is employed to create maximum magnetic flux around the proprietary voice coil for increased sensitivity when compared to similar sized exciters. In turn, this reduces power requirements and makes it possible to use very small audio amplifiers, without sacrificing total output. The 1" voice coil allows for more input power, creating rich, dynamic sound.
To ensure maximum acoustic energy transfer between the transducer and the surface to which it is attached, 3M VHB (Very High Bond) adhesive is pre-applied to the main body, and the four arms ... just peel and stick! Two spring-loaded terminals are built onto the main body for quick electrical connection.
Note: An exciter's frequency response and sensitivity are completely dependent on the exciter's designated surface. Thinner, smaller materials will tend to be louder and create a mid/tweeter response. Thicker, larger materials (with multiple exciters) will be slightly quieter but result in a more full-range sound.
Specifications: Power handling: 20 watts RMS VCdia: 25 mm Nominal impedance: 4 ohms Re: 4.3 ohms Le: 0.25 mH Fs (uncoupled): 224 Hz Dimensions: 3.99" (101.44 mm) overall diameter x 0.97" (24.7 mm) total height Weight: 90.5 grams.
To learn more about Dayton Audio Exciters, and for help on which Exciter is right for you, check out .
Product Details | |
|---|---|
| Brand | Dayton Audio |
| Model | DAEX25Q-4 |
| Part Number | 295-228 |
| UPC | 848791001024 |
| Unit of Measure | Each |
| Weight | 0.25 |
Product Specifications | |
|---|---|
| Application | Full-Range Exciter |
| Power Handling (RMS) | 20 Watts |
| Impedance | 4Ω |
Attention CA Residents: Prop 65 Warning
WARNING:
This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item
Our staff are available to answer any questions you may have about this item
Look Similar Items By Category
Customer Reviews
By Jeremy Sasser
Date: December 20, 2022
The only thing I didn't like about this particular model is the clip type speaker inputs. I removed them and just soldered directly to them - absolutely amazed me when I first powered it on without it being attached to anything, I actually attached it to a trash can and was able to semi-tune it by how much and dense the trash in the trash can had. Extremely cool product.
Rating: 
[5 of 5 Stars!]
[5 of 5 Stars!]
By Josh
Date: May 21, 2022
The sound reproduction is amazing I was completely impressed. I put 2 of these and 2 other ones on my above the headliner in my car for a more immersive sound and ran them all through 300hz bass blockers cause I dont need them to reproduce low frequencies. They pack a punch for as small as they are. Very happy.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Blueowlbc
Date: April 11, 2022
Grade upgrade for the AtGames Legend ALP pinball machine. The stock exciters were horrible, these solved the issue of poor sound and vibrating. Installed them on the inside bottom
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Eric
Date: April 06, 2022
Exceeded my expectations the sound is amazing!
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Dave amp; Judy Williams
Date: March 19, 2022
I've built a lot of speakers, transmission line, horn, ported, motion feedback etc.The result from a simply attached driver to a board is just stunning. Sure, bass is lacking but the use of a sub is generally needed anyway.Much easier to include a set of these speakers in a room and have great sound than any previous speaker built.I will not be removing these.
Rating: [5 of 5 Stars!]
[5 of 5 Stars!]
By Marcieanne
Date: February 02, 2022
He loves these and has been trying different configurations. One of the units had poor adhesive or it would be 5 stars. Now he wants some higher quality units. They are so versatile and sound great for the price.
Rating: 
[4 of 5 Stars!]
[4 of 5 Stars!]