skip to footer block
LJ Cannon TAB LOCK BASE 2207001 Image for Reference P662331LJ-1487001 https://cdnimages.opentip.com/full/LJ/LJ-1487001.jpg Cannon TAB LOCK BASE 2207001 Image for Reference Manufacturer Part Number: 2207001Cannon TAB LOCK BASE 2207001Tab Lock BasePut your downrigger in position to reel in the big one.Price is only for Item# LJ-1487001: Cannon TAB LOCK BASE 2207001.The following items are not included, you can buy the following items by searching the item#:Item# LJ-1487003: Cannon CANNON SWIVEL BASE 2207003.Item# LJ-1481001: Cannon MOUNTING BASE-MAGNUM 1904040. 662331 012977300281 3.88lbs 3.25 9.75 15.75
Cannon
36.6500 2023-07-02 Only 4 left In Stock
customer review - by , October 10, 2013
3/ 5stars
had to add one quarter inch shim plate to under side of downrigger base to fit snugly in mounting base.
customer review - by , July 7, 2013
4/ 5stars
Could be better if it was aluminum. I worry about the strength of the product and the ability to last from a lot of use.
customer review - by , July 7, 2013
4/ 5stars
I have a pair of downriggers and use these bases, I've broken two bases - one from snagging a ball on a reef, and the other when the cable got caught in my kicker. I was lucky not to lose the downrigger on both occasions - when it snagged the reef I grabbed the DR and held it until the cable broke. That was with 180lb stainless cable.Unfortunately if the base were stronger, the downrigger might break instead, so it's better to have this cheap part break instead of the downrigger, but IMO the downrigger should be tied to a cleat with a short piece of rope as a safety precaution, and the rod-holder on the downrigger should not be used so the rod doesn't go overboard if the DR snaps off.
customer review - by , July 7, 2013
5/ 5stars
I have Cannon Easi-Troll 2 donriggers and these work very good at holding them onto my boat, I suggest using a strong backing plate if bolting thru 1/4 or thinner decks, fender washers work great with decks thicker then 1/4.
customer review - by , June 6, 2013
5/ 5stars
I needed a set of these for a new boat. They work great with my downriggers. And as usual, good Cannon quality.
customer review - by , January 1, 2012
3/ 5stars
Advertised that it will fit a mini mag,it does NOT fit the Cannon mini mag downrigger that I have. I will have to file/sand down the downrigger base for this thing to fit.
Share to:

Cannon TAB LOCK BASE 2207001 (Image for Reference), Price/Each

stars Rating 4 | 6 reviews
Brand Cannon
See other products from LJ

Upc: 012977300281
SKU: LJ-1487001
Price: $36.65
Quantity:
Only 4 left In Stock
Click "Add to Cart" to calculate shipping and delivery time.
Share & Earn 10% Cash Back Best Price in Bulk

Product Description

Price is for Each.

Manufacturer Part Number: 2207001

Cannon TAB LOCK BASE 2207001

Tab Lock Base

Put your downrigger in position to reel in the big one.

Price is only for Item# LJ-1487001: Cannon TAB LOCK BASE 2207001.
The following items are not included, you can buy the following items by searching the item#:
Item# LJ-1487003: Cannon CANNON SWIVEL BASE 2207003.
Item# LJ-1481001: Cannon MOUNTING BASE-MAGNUM 1904040.

warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.
Need more information?
Our staff are available to answer any questions you may have about this item


Customer Reviews
By jesse wayne roberts
Date: October 02, 2013
had to add one quarter inch shim plate to under side of downrigger base to fit snugly in mounting base.
Rating: 3 stars [3 of 5 Stars!]
By dave
Date: July 29, 2013
Could be better if it was aluminum. I worry about the strength of the product and the ability to last from a lot of use.
Rating: 4 stars [4 of 5 Stars!]
By Josh
Date: July 22, 2013
I have a pair of downriggers and use these bases, I've broken two bases - one from snagging a ball on a reef, and the other when the cable got caught in my kicker. I was lucky not to lose the downrigger on both occasions - when it snagged the reef I grabbed the DR and held it until the cable broke. That was with 180lb stainless cable.Unfortunately if the base were stronger, the downrigger might break instead, so it's better to have this cheap part break instead of the downrigger, but IMO the downrigger should be tied to a cleat with a short piece of rope as a safety precaution, and the rod-holder on the downrigger should not be used so the rod doesn't go overboard if the DR snaps off.
Rating: 4 stars [4 of 5 Stars!]
By TFB "Tom"
Date: July 16, 2013
I have Cannon Easi-Troll 2 donriggers and these work very good at holding them onto my boat, I suggest using a strong backing plate if bolting thru 1/4 or thinner decks, fender washers work great with decks thicker then 1/4.
Rating: 5 stars [5 of 5 Stars!]
By bakerjw "Bakerjw"
Date: June 04, 2013
I needed a set of these for a new boat. They work great with my downriggers. And as usual, good Cannon quality.
Rating: 5 stars [5 of 5 Stars!]
By KillerBee
Date: January 11, 2012
Advertised that it will fit a mini mag,it does NOT fit the Cannon mini mag downrigger that I have. I will have to file/sand down the downrigger base for this thing to fit.
Rating: 3 stars [3 of 5 Stars!]
Items 1 - 6 of 6 reviews
 1