skip to footer block
EAT Cal Van CV95400 In Line Dowel Pin Puller P4181940EAT-CV95400 https://cdnimages.opentip.com/full/EAT/EAT-CV95400.jpg Cal Van CV95400 In Line Dowel Pin Puller Manufacturer Part Number: 95400New Dowel Pin Puller that extracts Dowels withoutthe use of a slide hammer.Fit the appropriate sized collet over the dowel, tighten the sleeve, Use outer sleeve and nut toextract the dowel.Can be used with air ratchet, or traditional ratchet.Elimination of the slide hammer saves cost as wellas effort and potential hand injury.SAE Set includes 3/16, 1/4, 5/16, 3/8, and 1/2Metric Set Includes 4, 5, 6, 8, 10, and 12MMMaster Set includes both SAE and Metric Collets 4181940 047084954003 4.6500lbs 2.10 11.50 7.50
Cal-Van Tools
203.9500 2025-04-25 Out of Stock
customer review - by , October 10, 2023
5/ 5stars
I purchased the puller hoping it would work to pull the 4-engine block Dow pins that have most likely been in the Deuce and a half since 1970 and it really worked well, a little sandpaper to rough up the exposed part of the Dow pin and installed the puller on top and pulled right out so easy I was surprised.
customer review - by , October 10, 2023
4/ 5stars
Worked like a charm to remove all 3 cylinder head dowels on top of block
customer review - by , September 9, 2023
5/ 5stars
After many attempts with other tools only this dowel pin remover was able to help me fix my Hobart mixer.
customer review - by , June 6, 2023
4/ 5stars
A pretty expensive piece of kit, but worked as advertised -- I've read others had issues with the parts breaking, but I had no issue with it, I was just careful not to over tighten/torque anything -- pulled the pins out I needed (the smallest tool is the one I needed) ... good to have in the tool arsenal, but certainly not cheap. 4 out of 5 because of the price.
customer review - by , April 4, 2023
4/ 5stars
This tool fell apart on me the first time I used it. The collets broke from too much pressure. I was tightening by hand as hard as I could because the tool was slipping. The main sleeve that the collet goes into cracked and made the kit useless. I was not able to finish the job.
customer review - by , September 9, 2022
5/ 5stars
This simply would not work as advertised. I watched the videos online about this exact tool and tried several times with zero results.
customer review - by , April 4, 2022
5/ 5stars
makes pin removal easy.
customer review - by , October 10, 2021
5/ 5stars
Did the job well!
customer review - by , August 8, 2021
5/ 5stars
It's good tool for me to use.
customer review - by , August 8, 2021
5/ 5stars
This unit works and it works well. The tool extracts pins and doesn't scratch or scuff the coated parts I use it on.
  »  
  »  
  »  
  »  
  »  

Cal-Van CV95400 In Line Dowel Pin Puller

stars Rating 5 | 14 reviews
Brand Cal-Van Tools
Shop more from EAT
UPC: 047084954003
SKU: EAT-CV95400
Price:
$203.95& this item ships for FREE Shipping. Details
Quantity:
Out of Stock
*  Click "Add to Shopping List" to save the item for later purchase. You can receive a notice email when it is back in stock.
Share & Earn 10% Cash Back

Product Description

Free Shipping Promotion
This item qualifies for free shipping within US 48 states. Details.

Manufacturer Part Number: 95400

  • New Dowel Pin Puller that extracts Dowels withoutthe use of a slide hammer.
  • Fit the appropriate sized collet over the dowel, tighten the sleeve, Use outer sleeve and nut toextract the dowel.
  • Can be used with air ratchet, or traditional ratchet.
  • Elimination of the slide hammer saves cost as wellas effort and potential hand injury.
  • SAE Set includes 3/16, 1/4, 5/16, 3/8, and 1/2
  • Metric Set Includes 4, 5, 6, 8, 10, and 12MM
  • Master Set includes both SAE and Metric Collets

    • warning tips WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.p65warnings.ca.gov.

    Product Warranty

    This item has lifetime warranty.

    Return Policy

    All EAT- items are returnable, except for Open Box Scan Tools. scan tools/electronics, air tool are non-returnable

    Note

    This product is not eligible for coupon code discount, for we've been offering the best price in the market.
    Need more information?
    Our staff are available to answer any questions you may have about this item
    Request More Information

    Look Similar Items By Category

    Industrial & Scientific > Power & Hand Tools > Industrial Hand Tools > Tool Sets
    Tools & Home Improvement > Power & Hand Tools > Hand Tools > Tool Sets
    Customer Reviews
    5 out of 5
    see all 14 reviews
    5 stars
    11
    4 stars
    3
    3 stars
    0
    2 stars
    0
    1 stars
    0
    Write a Review
    By NCreloader
    Date: October 11, 2023
    I purchased the puller hoping it would work to pull the 4-engine block Dow pins that have most likely been in the Deuce and a half since 1970 and it really worked well, a little sandpaper to rough up the exposed part of the Dow pin and installed the puller on top and pulled right out so easy I was surprised.
    Rating: 5 stars [5 of 5 Stars!]
    By Derrick Henggeler
    Date: October 05, 2023
    Worked like a charm to remove all 3 cylinder head dowels on top of block
    Rating: 4 stars [4 of 5 Stars!]
    By darrell sikes
    Date: September 09, 2023
    After many attempts with other tools only this dowel pin remover was able to help me fix my Hobart mixer.
    Rating: 5 stars [5 of 5 Stars!]
    By Guido von Stennetti
    Date: June 27, 2023
    A pretty expensive piece of kit, but worked as advertised -- I've read others had issues with the parts breaking, but I had no issue with it, I was just careful not to over tighten/torque anything -- pulled the pins out I needed (the smallest tool is the one I needed) ... good to have in the tool arsenal, but certainly not cheap. 4 out of 5 because of the price.
    Rating: 4 stars [4 of 5 Stars!]
    By Matthew Gentile-Polese
    Date: April 19, 2023
    This tool fell apart on me the first time I used it. The collets broke from too much pressure. I was tightening by hand as hard as I could because the tool was slipping. The main sleeve that the collet goes into cracked and made the kit useless. I was not able to finish the job.
    Rating: 4 stars [4 of 5 Stars!]
    By David Grigolla
    Date: September 29, 2022
    This simply would not work as advertised. I watched the videos online about this exact tool and tried several times with zero results.
    Rating: 5 stars [5 of 5 Stars!]
    Items 1 - 6 of 14 reviews
     1  2  3  [Next]