The HI 9828 multiparameter meter with GPS receiver monitors up to 13 different water quality parameters (6 measured, 7 calculated). Measurements include pH, pH/mV, ORP, % saturation DO, mg/L DO, EC, absolute EC, resistivity, TDS, salinity, seawater specific gravity, atmospheric pressure and temperature.
The HI 9828 has a graphic, backlit LCD that automatically sizes the digits to fit the screen and allows full configuration of each parameter measured along with on-screen graphing capability. The meter incorporates comprehensive GLP features and the downloading of data via USB connection.
Each parameter is supported by on-screen context sensitive help, both in the calibration mode and during measurement.
Designed for outdoor environments, the meter is impact resistant and waterproof meeting IP67 standards (30 minutes immersion under 1 m of water). The multi-sensor probe can be left underwater in accordance with IP68 standards.
HI 769828 Multiparameter, Intelligent Probe
HANNA’s HI 769828 multiparameter probe incorporates a built-in microprocessor and amplifier that convert the high impedance signals from the sensors of the probe to eliminate common problems such as cable length limitations and noise associated with high impedance signals.
This allows the probe to have a reliable communication with the meter and also immediately warns the user of problems such as a broken cable. The standard cable lengths of the probe are 4, 10 and 20 meters (13, 32 and 64 feet) and custom lengths are also available.
The probe also features HANNA’s Quick Calibration which allows the user to calibrate pH and conductivity with one solution in a single, simple step. Dissolved oxygen is also calibrated in one step in saturated air. The probe houses 5 of the 6 measured parameters: pH, ORP, EC, dissolved oxygen and temperature. The sensors are all independently replaceable and are easy to maintain and keep clean. The sensors are protected by an outer PVC/stainless
steel sleeve and cap which is suitable for use in 2” wells. The probe housing complies with IP68 standard.
Sensor replacement is quick and easy with screw type connectors and color coded sensors.
The Galvanic DO sensor does not require polarization time so it’s ready at a moment’s notice.
The 4-ring conductivity system ensures stable conductivity readings that are immune to surface coating. Absolute conductivity, temperature corrected conductivity, salinity, specific gravity and TDS determinations are possible with measurements from this sensor.
The HI 9828 automatically recognizes the presence of either the pH or pH/ORP sensor.
Both sensors have a cloth junction which allows greater sensitivity, and are gel filled for improved resistance to contamination.
The meter also displays pH in mV readings—ideal for troubleshooting.
Fast Tracker™—Tag Identification System
HANNA’s Fact Tracker™—Tag Identification System simplifies test logging. iButton®s with a unique ID can be installed at various sampling sites. When the matching connector on the meter contacts the location button, measurements are logged and labeled with the alphanumeric user-entered location ID. Location, date, time and measurements are logged into the meter which can be transferred to a PC. The Fast Tracker™ system complements the GPS for ultimate tracking.
iButton® Tags are Easy to Install
Install the optional TAGs near your sampling points for quick and easy iButton® readings. Each TAG contains a computer chip with a unique identification code encased in stainless steel. You can install a practically unlimited amount of TAGs. Additional TAGs can be ordered for all of your traceability requirements.
Choose your configuration -
HI 9828/4-01 HI 9828 and 4 m (13.1’) probe cable, no GPS, 115VAC
HI 9828/4-02 HI 9828 and 4 m (13.1’) probe cable, no GPS 230VAC
HI 9828/10-01 HI 9828 and 10 m (33’) probe cable, no GPS, 115VAC
HI 9828/10-02 HI 9828 and 10 m (33’) probe cable, no GPS, 230VAC
HI 9828/20-01 HI 9828 and 20 m (66’) probe cable, no GPS, 115VAC
HI 9828/20-02 HI 9828 and 20 m (66’) probe cable, no GPS, 230VAC
HI 9828/30-01 HI 9828 and 30 m (98’) probe cable, no GPS, 115VAC
HI 9828/30-02 HI 9828 and 30 m (98’) probe cable, no GPS, 230VAC
HI 9828/40-01 HI 9828 and 40 m (131’) probe cable, no GPS, 115VAC
HI 9828/40-02 HI 9828 and 40 m (131’) probe cable, no GPS, 230VAC
HI 9828/50-01 HI 9828 and 50 m (164’) probe cable, no GPS, 115VAC
HI 9828/50-02 HI 9828 and 50 m (164’) probe cable, no GPS, 230VAC
HI 9828/60-01 HI 9828 and 60 m (200’) probe cable, no GPS, 115VAC
HI 9828/60-02 HI 9828 and 60 m (200’) probe cable, no GPS, 230VAC
HI 9828/70-01 HI 9828 and 70 m (230’) probe cable, no GPS, 115VAC
HI 9828/70-02 HI 9828 and 70 m (230’) probe cable, no GPS, 230VAC
HI 9828/80-01 HI 9828 and 80 m (262’) probe cable, no GPS, 115VAC
HI 9828/80-02 HI 9828 and 80 m (262’) probe cable, no GPS, 230VAC
HI 9828/90-01 HI 9828 and 90 m (295’) probe cable, no GPS, 115VAC
HI 9828/90-02 HI 9828 and 90 m (295’) probe cable, no GPS, 230VAC
HI 9828/100-01 HI 9828 and 100 m (328’) probe cable, no GPS, 115VAC
HI 9828/100-02 HI 9828 and 100 m (328’) probe cable, no GPS, 230VAC
HI 9828 configurations are supplied with HI 769828 multisensor probe (pH/ORP, EC, DO, temperature), HI 9828-25 quick calibration standard solution (500 mL), probe maintenance kit, rechargeable C size Ni-MH batteries (4), power adapter & cable, car 12V accessory outlet adapter, HI 7698281 USB interface cable, HI 92828 Windows® compatible software and instruction manual in a rugged carrying case.
|pH||Range||0.00 to 14.00 pH|
|mV of pH Input||Range||±600.0 mV|
|Range||0.0 to 500.0% / 0.00 to 50.00 mg/L|
|Resolution||0.1% / 0.01 mg/L|
|Accuracy||0.0 to 300.0%: ±1.5% of reading or ±1.0% whichever is greater; 300.0 to 500.0%: ±3% of reading; 0.00 to 30.00 mg/L: ±1.5% of reading or 0.10 mg/L whichever is greater; 30.00 mg/L to 50.00 mg/L: ±3% of reading|
|Conductivity||Range||0.000 to 200.000 mS/cm (absolute EC up to 400 mS/cm)|
|Resolution||manual: 1 ?S/cm; 0.001 mS/cm; 0.01 mS/cm; 0.1 mS/cm; 1 mS/cm; automatic: 1 ?S/cm from 0 to 9999 ?S/cm; 0.01 mS/cm from 10.00 to 99.99 mS/cm ; 0.1 mS/cm from 100.0 to 400.0 mS/cm; automatic mS/cm: 0.001 mS/cm from 0.000 to 9.999 mS/cm; 0.01 mS/cm from 10.00 to 99.99 mS/cm; 0.1 mS/cm from 100.0 to 400.0 mS/cm|
|Accuracy||±1% of reading or ±1 ?S/cm whichever is greater|
|Resistivity||Range||0 to 999999 Ωcm; 0 to 1000.0 kΩcm; 0 to 1.0000 MΩcm|
|Resolution||dependent on resistivity reading|
|TDS||Range||0 to 400000 mg/L or ppm (the maximum value depends on the TDS factor)|
|Resolution||manual: 1 mg/L (ppm); 0.001 g/L (ppt); 0.01g/L (ppt); 0.1 g/L (ppt); 1 g/L (ppt); autorange scales: 1 mg/L (ppm) from 0 to 9999 mg/L (ppm); 0.01 g/L (ppt) from 10.00 to 99.99 g/L (ppt); 0.1 g/L (ppt) from 100.0 to 400.0 g/L (ppt); autorange g/L (ppt) scales: 0.001 g/L (ppt) from 0.000 to 9.999 g/L (ppt); 0.01 g/L (ppt) from 10.00 to 99.99 g/L (ppt); 0.1 g/L (ppt) from 100.0 to 400.0 g/L (ppt)|
|Accuracy||±1% of reading or ±1 mg/L (ppm) whichever is greater|
|Salinity||Range||0.00 to 70.00 PSU (Extended Practical Salinity Scale)|
|Accuracy||±2% of reading or 0.01 PSU whichever is greater|
|Range||0.0 to 50.0 σt, σ0, σ15|
|Resolution||0.1 st, s0, s15|
|Accuracy||±1 σt, σ0, σ15|
|Atm. Pressure||Range||450 to 850 mmHg; 17.72 to 33.46 inHg; 600.0 to 1133.2 mbar; 8.702 to 16.436 psi; 0.5921 to 1.1184 atm; 60.00 to 113.32 kPa|
|Resolution||0.1 mmHg; 0.01 inHg; 0.1 mbar; 0.001 psi; 0.0001 atm; 0.01 kPa|
|Accuracy||±3 mmHg within ±15°C from the calibration temperature|
|Temperature||Range||-5.00 to 55.00°C; 23.00 to 131.00°F; 268.15 to 328.15K|
|Resolution||0.01°C; 0.01°F; 0.01K|
|Accuracy||±0.15°C; ±0.27°F; ±0.15K|
|Calibration||pH||automatic one, two, or three points with five memorized standard buffers (pH 4.01, 6.86, 7.01, 9.18, 10.01) or one custom buffer|
|ORP||automatic at one custom point|
|Conductivity||automatic one point with six memorized standards (84 ?S/cm, 1413 ?S/cm, 5.00 mS/cm, 12.88 mS/cm, 80.0 mS/cm, 111.8 mS/cm) or custom point|
|DO||automatic one or two points at 0, 100% or one custom point|
|Resistivity, TDS, σ||based on conductivity or salinity calibration|
|Salinity||one custom point|
|Atm. Pressure, |
|automatic at one custom point|
|automatic from -5 to 55°C (23 to 131°F)|
|Logging Memory||up to 60,000 samples with 13 measurements each|
|Logging Interval||1 second to 3 hours|
|USB (with HI 929829 software)|
|meter IP67, probe IP68|
|Environment||0 to 50°C (32 to 122°F); RH 100%|
|Power Supply||1.5V alkaline C cells (approximately 150 hours of continuous use without backlight) (4) / 1.2V rechargeable C cells (approximately 70 hours of continuous use without backlight) (4)|
|221 x 115 x 55 mm (8.7 x 4.5 x 2.2") / 270 x 46 mm DIA (10.6 x 1.8" DIA)|
|Weight||meter: 750 g (26.5 oz.); probe: 750 g (26.5 oz.)|
Hanna Instruments products are manufactured in our ISO 9001 facilities, meeting the highest quality standards in the industry. Hanna's high standards also apply should a product be returned due to defects in material or workmanship. Our extensive warranty extends up to three years on some products. Limitations: Warranted products may be returned for repair or replacement only at the discretion of Hanna Instruments. In some circumstances, remedy may constitute refund for the price paid for the product.
The warranty period commences from the original date of sale to the user or a maximum of 18 months from factory ship date. Warranty is valid only when the product is used under normal conditions and in accordance with operating limitations and prescribed maintenance procedures. The express warranty stated previously is the only express warranty given by Hanna to the end-user buyer. Hanna expressly disclaims any warranties implied by law, including but not limited to warranty of merchantability of fitness for a particular purpose. Hanna shall not be liable for any individual or consequential damages of any kind for breach of any warranty, negligence, on the basis of strict liability or otherwise. Hanna's warranty periods are:
If you want to:
- Make product changes;
- Create something not in stock
6,000 + (and growing) factories in our existing network are eager to make it for you.
When it comes to selling in stock products, we are no difference from many other Internet retailers, but we take pride in going extra miles to do something special for you: Have some products custom made for you.
We cannot do everything, but we usually can accommodate a certain changes in product options such as color, size, material, or minor design twist. We primarily work with vendors or factories, not individual artist or craftsman. For custom made products, we usually only cater to bulk size order that meets the minimum quantity requirement of a single factory run. Don't be shy. Ask. What we can accomplish may surprise you!
Read this first: Copyrights & Trademarks
Thank You for Your Request!If we can meet your requirements, we'll contact you within 1 business day.
Get 5% Reward by Sharing
Login with your Opentip.com account to continue.
View Your Earnings
Get 5% Reward by Sharing
Refer friends and get rewards when they make their purchase.
View Your Earnings